AMX RE-DM6, RE-DM4 Hardware Issues, Troubleshooting hardware, Hardware Checklist, To check this

Page 88

Appendix B: Troubleshooting

Hardware Issues

The following items address hardware related technical support issues.

You should make sure that each AxLink device number is a unique number. Duplicate AxLink device numbers will cause problems. The same holds true for SEND_STRING pack numbers, so do not duplicate pack numbers as well.

Troubleshooting hardware

The following table shows the different areas that should be checked if a hardware problem arises.

Hardware Checklist

To check this

Type this, then press Enter.

 

 

Verify Status of AxLink DIP switch

Default is 6 & 7 on, all others off, which makes the Radia device 96

 

 

Verify Status of Low Voltage Cables

• Wiggle check

 

• Correct position?

 

• Good strong connection?

 

• Verify with wiring diagram or manual.

 

 

Verify Status of Loads

• Have loads been checked for shorts?

 

• Have loads been verified to work (Bypass module)?

 

• Check for transformers.

 

• Electronic or magnetic?

 

• Transformer rating (overload)?

 

 

Verify Status of Wires

• Correct voltage?

 

• Correct phase?

 

• One Neutral per controlled Zone?

 

• Check for common neutrals.

 

• Wires connected to correct terminal?

 

• Are all multi-phase line terminals connected?

 

 

You can verify Radia Eclipse can turn the loads on/off by turning off all AxLink switches. This will set all circuits to 100%.

80

RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules

Page 87 Page 89
Image 88
Page 87 Page 89
Contents Radia Eclipse Dimmer Modules AMX Limited Warranty and Disclaimer Page Page Table of Contents Radia Lighting System Configuration Pages Initial Level Status Reporting Appendix a AMX Lighting Curves Overview Radia Eclipse RE-DM4 Dimmer ModuleRE-DM4 Specifications RE-DM4 SpecificationsDimmed Switched Suggested LoadsRE-DM4 4-pin module connector male Line-In ConnectionsRE-DM4 Lighting Application Drawings Lighting Application for the RE-DM4, Example aRadia Eclipse RE-DM6 Dimmer Module RE-DM6 6-channel Integrated Dimmer ModuleSuggested Installation Loads RE-DM6 SpecificationsRE-DM6 Specifications Line-In Connections for the RE-DM6 RE-DM6 Lighting Application Drawings Lighting Application for the RE-DM6, Method aFeatures ApplicationsAMX Lighting Control Equipment AMX Lighting Control EquipmentIntegrated dimmer control modules Dimmer AccessoriesDimmer modules Power considerations Wiring ConsiderationsSpace Requirements Conduit Knockout locations RDA-ENC2 used as exampleRDA-ENC2, -ENC4, and -ENC6 enclosure and dimensions RDA Enclosure DimensionsRDA-ENC6B and RDA-ENC12B enclosures and dimensions Mounting AMX Lighting Enclosures Distance a to BConnecting High-Voltage, Single-Phase Input Power and Loads High-Voltage ConnectionsRDA-ENC6B 120/240 VAC Line Input Single Phase RDA-ENC6B 120 VAC Single Phase Line InputConnecting High-Voltage Input Power and Loads RDA-ENC6B 120/208 VAC line input three phase RDA-ENC6B 120/208 VAC three-phase 4 W + G wiring diagramRDA-ENC6B Three Phase Line Input Connector Reference RDC-PFC Power Distribution And Line Input ReferencesInstalling RDM Modules Into an RDA Enclosure Enclosure module mounting slots and mounting screw holesLow-Voltage Connections Green LED Status IndicatorModule Connections Red LED Status Indicators RE-DM4 only Configuring and connecting multiple controllersSW1 DIP Switch Setting Values for AxLink Configuring and Connecting AxLinkValue External power Connecting Dry ClosuresDry Closures Failsafe InputDefault Settings Default Low-End SettingsDefault preset time values Default PresetsRadia Lighting System Configuration Pages Lighting System LinkRadia Configuration Manager Main Lighting SystemDevice Configuration Device ConfigurationPresets section Preset Configuration Radia Lighting System Configuration Pages AMX Radia Lighting Programming SoftwarePreset Status Presets Defined vs. Undefined LevelsPreset # Lighting Systems Overview Sample AMX Lighting controller and internal componentsProgramming Commands Control Curves and Low-End SettingsDefault Low-end Default Ramp TimeDefault Ramp Time LevelsAMX Lighting Channel Commands ChannelsSENDSTRINGs Protocol ConventionsRamp Dimmers Up Ramp Dimmers DownRamp Dimmers Up Ramp Dimmers DownRamp Active Preset Down Ramp Active Preset UpStop Ramping Dimmer Stop Ramping Preset Recall PresetRecord Preset Level StatusSet Curve Curve StatusSet Low End Low End StatusReboot Set Default Level TimeSet Default Preset Time Dimmer StatusRamp To Level Set Default Ramp TimeUndefine Dimmer Factory Default Phase QueryVersion Query SENDCOMMANDs Ramp Preset Up NEWSendcommand Protocol Conventions Ramp Preset UpStop Ramping Preset NEW Ramp Preset Down NEWRamp Preset Down Reboot NEW Curve Status NEWSet Low End NEW Low End Status NEWUndefine Dimmer NEW Phase Query NEW Sendcommand Radia,?YAppendix a AMX Lighting Curves Basic dimming curve Curves Curve ConfigurationCurves Standard Dimming Curve Load Type CurvesCurve 1 Voltage Output in 240V AC Curve 1 with Low End Setting @ 5%, 10%, and 20% Volts RMS Economical Dimming Curve10VDC Curve Curve 2 at 240 VACCurve 3 at 120 VAC 12VDC Curve Curve 4 Voltage output in Volts RMSLutron FDB Curve Curve 4 Voltage output in volts DCCurve 5 at 240 VAC Advance Mark VII Curve Curve 6 Voltage output in Volts RMS12% Roll Off Curve 6 Voltage output in volts DCCurve 7 Voltage output in Volts RMS 19% Roll Off Curve 8 at 120 VAC33% Roll Off Curve 8 Voltage output in volts DCCurve 9 Voltage output in Volts RMS Curve #1 a Curve a at 120 VACLog-Curve #1 B Curve a Voltage output in volts DCCurve B Voltage output in Volts RMS Log-Curve #2 C Curve C at 120 VACCurve #2 D Curve C Voltage output in Volts DC10% Off Curve N Curve D Voltage output in Volts RMSAlways OFF Curve O Curve N at 240 VACAlways on Curve F Curve O at 240 VACCurve F at 240 VAC Curve R at 120 VAC Curves 5 & B on the Radia Eclipse RE-DM6 at 120 VAC Curves a & D at 120 VAC Page Software Issues Using Pass modeTesting AMX Lighting features Testing procedures for AMX Lighting featuresHardware Issues Troubleshooting hardwareHardware Checklist To check thisPage Increase Your Revenue through education + knowledge
Related manuals
Manual 2 pages 38.75 Kb Manual 2 pages 7.17 Kb

RE-DM4, RE-DM6 specifications

The AMX RE-DM4 is a cutting-edge solution in the realm of digital media management, designed to cater to the complexities of modern broadcasting environments. This advanced device aims to streamline workflows, enhance media asset management, and ensure optimal media delivery across various platforms.

One of the standout features of the AMX RE-DM4 is its robust interface, which allows users to interact with the system intuitively. The device incorporates a user-friendly GUI that enables operators to manage media assets effortlessly. The interface supports drag-and-drop functionalities, which greatly simplifies the process of uploading, organizing, and retrieving digital content.

The AMX RE-DM4 also boasts innovative multimedia processing capabilities, allowing it to handle high-resolution video formats with ease. The device supports a range of codecs, ensuring compatibility with the latest video and audio standards. This versatility is crucial for broadcasters who frequently work with diverse media types and formats.

Furthermore, the AMX RE-DM4 features advanced metadata tagging and search functionalities. This technology empowers users to tag media assets with critical information, enabling quick retrieval and efficient categorization. The integrated search engine is designed to facilitate instant searches, thereby reducing downtime and improving overall productivity.

Another notable characteristic of the AMX RE-DM4 is its scalability. The system is designed to grow alongside evolving media requirements, making it an ideal choice for both small studios and large broadcasting networks. With modular components and expandable storage options, users can easily upgrade their systems as their needs change.

In terms of connectivity, the AMX RE-DM4 includes multiple input and output options, ensuring seamless integration with existing studio equipment and networks. It supports various protocols, which enhances compatibility with other devices and allows for more fluid media workflows.

Security is a crucial aspect of digital media management, and the AMX RE-DM4 addresses this by incorporating robust encryption and access control features. Users can set permissions for different team members, safeguarding sensitive content while still allowing collaborative work environments.

In conclusion, the AMX RE-DM4 emerges as a powerful tool for media professionals, integrating state-of-the-art technologies and features that enhance efficiency and productivity. Its intuitive interface, multimedia processing capabilities, advanced search options, scalability, and robust security measures make it a valuable asset in the fast-paced world of digital media management. This device exemplifies a forward-thinking approach to media handling, positioning itself as a leader in the industry.
Top Page Image Contents