Philips GC2030 manual Troubleshooting, Problem Possible causes

Page 11

ENGLISH 11

Troubleshooting

This chapter summarises the most common problems you could encounter with your iron. Please read the different sections for more details. If you are unable to solve the problem, please contact the Philips Customer Care Centre in your country. See the worldwide guarantee leaflet for telephone numbers of the or visit our website at www.philipsonline.com.

Problem

Possible cause(s)

The iron is plugged in but the soleplate

Connection problem.

is cold.

 

 

Temperature dial set at MIN.

No steam

Not enough water in the water tank.

 

The steam control has been set to

 

position O.

 

The soleplate is not hot enough

 

and/or the Drip Stop function (types

 

GC2030, 2025, 2020) has been

 

activated.

Solution

Check the mains cord, the plug and the wall socket.

Set the temperature dial to the required temperature.

Fill the water tank (see Filling the water tank).

Set to steam position q or w (see Steam ironing).

Set the temperature dial to a temperature in the steam area (2 to MAX). Put the iron on its heel and wait until the amber pilot light has gone out before you start ironing.

No Shot of Steam (type GC2010,

The (Vertical) Shot of Steam function

Put the iron in horizontal position and

2011, 2015, 2016, 2025, 2030 only) or

has been used too often within a very

wait for a while before using the

no Vertical Shot of Steam (Types

short period.

(Vertical) Shot of Steam function

GC2030, 2025,2016, 2015 only)

 

again.

 

 

 

The soleplate is not hot enough.

Set the temperature dial to a temperature in the steam area (2 to MAX). Put the iron on its heel and wait until the amber pilot light has gone out before you start ironing.

Flakes and impurities come out of the

Hard water forms flakes inside the

Use the Calc-Clean function a few

soleplate during ironing.

soleplate.

times (see 'Calc-Clean').

Red pilot light is blinking (type GC2030

The auto shut-off function has been

Shake the iron lightly to deactivate the

only).

activated. See "Automatic shut-off"

auto shut-off function: the pilot light

 

section.

will stop blinking.

 

 

 

Water drips out of the soleplate (types

The temperature has been set too

Set the temperature dial to a

GC2016, 2015, 2011, 2010, 2006, 2005

low.

temperature in the steam area (2

only).

 

to MAX). Put the iron on its heel and

 

 

wait until the amber pilot light has

 

 

gone out before you start ironing.

 

 

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Page Page English Deutsch Norsk Svenska Suomi Dansk This will cease after a short while Before first useFilling the water tank Never use the appliance if it is damaged in any wayFor auto-shut-off versions only type GC2030 Setting the temperaturePut the iron on its heel Spraying Other featuresSteam ironing Ironing without steamAutomatic shut-off type GC2030 only Drip Stop types GC2030, 2025, 2020 onlyTo heat up the iron again Cleaning and maintenanceCalc-Clean After ironing After the Calc-Clean processStorage Information & serviceProblem Possible causes TroubleshootingLassen Sie das eingeschaltete Gerät niemals unbeaufsichtigt WichtigVor dem ersten Gebrauch Den Wasserbehälter füllenStecken Sie den Netzstecker in eine Schuko-Steckdose Einstellen der BügeltemperaturChemisch enthärtetes Wasser Bügelgut einsprühen DampfbügelnTrockenbügeln Andere AnwendungenNur Type GC 2030 Automatische Ausschaltung Nur Typen GC 2020, 2025 und 2030 Tropf-StopDampfreglers springt etwas hervor Die Bügelsohle wird wie folgt wieder beheiztReinigung und Wartung Geben Sie Acht, dass Sie sie Nadel nicht verbiegen Nach der Reingung mit Calc-CleanWiederholen Sie den Vorgang bei Bedarf Nach dem BügelnWasser. Gießen Sie das Wasser anschließend aus Information und ServiceAufbewahrung Auftragen könnenVermutliche Ursachen Das Gerät arbeitet nicht wie gewünscht?Bruk aldri apparatet hvis det på noen måte er skadet ViktigFør første gangs bruk Fylle på vannDamp-stryking Stille inn temperaturEkstra damp gjelder bare typene GC2020, 2006 Stryking uten dampAndre funksjoner Trykk og hold nede Superdamp-knappen For å varme opp strykejernet igjenDryppestopp gjelder bare typene GC2030, 2025 Automatisk slukking gjelder bare type GC2030Dra dampkontrollen litt opp og rist lett på strykejernet Calc-Clean-funksjonen fjerner kalk og urenheterRengjøring og vedlikehold Oppbevaring Etter Calc-Clean-prosessenEtter stryking Informasjon & service Problem Mulig årsak Løsning ProblemløsingAnvänd aldrig strykjärnet om det är skadat på något sätt ViktigtFöre första användning Påfyllnad av vattenbehållarenStäll strykjärnet på parkeringshälen Inställning av temperaturÅngstrykning Extra ånga endast modellerna GC2020, 2006 Strykning utan ångaÖvriga funktioner SprayAutomatisk avstängning endast modell GC2030 Uppvärmning av strykjärnet på nyttÅngpuffar endast modellerna GC2030, 2025, 2016, 2015, 2011 Droppstopp endast modellerna GC2030, 2025Ställ ångreglaget i läge Rengöring och underhållAvkalkning Förvaring Efter avkalkningenEfter strykningen Garanti och service Felsökning Problem Möjlig orsak ÅtgärdTämä loppuu kuitenkin nopeasti TärkeääKäyttöönotto Vesisäiliön täyttöVettä Lämpötilan valintaSuihkutus HöyrysilitysSilittäminen ilman höyryä Muut toiminnotAutomaattikatkaisu vain malli GC2030 Höyrysuihkaus vain mallit GC2030, 2025, 2016, 2015, 2011Höyrysuihkaus pystyasennossa vain mallit GC2030, 2025, 2016 Tippalukko vain GC2030, 2025Nosta höyryrauta ylös tai liikuta sitä hieman Calc-Clean-toimintoHöyryraudan uudelleen kuumentaminen Puhdistus ja hoitoIrrota pistotulppa pistorasiasta ja anna höyryraudan jäähtyä Silittämisen jälkeenNeuvonta & huolto SäilytysOngelma Mahdollinen syy Ratkaisu TarkistusluetteloVandpåfyldning VigtigtInden strygejernet tages i brug første gang Auto-sluk gælder kun type GC2030 TemperaturindstillingSilke Uld Bomuld, linned Ekstra kraftig damp kun type GC2020, 2006 DampstrygningTørstrygning uden damp Yderligere funktionerNedtrykket i højst 5 sekunder Lodret dampskud kun type GC2030, 2025, 2016Dryp-stop kun type GC2030, 2025 Auto-sluk kun type GC2030Træk lidt op i dampknappen og ryst forsigtigt strygejernet Sådan opvarmes strygejernet igenRengøring og vedligeholdelse Løft eller bevæg strygejernet lidtLad strygejernet afkøle helt, inden det stilles væk Efter Calc-Clean-processenEfter brug Tænd for strygejernet, så strygesålen tørrerOpbevaring Information og serviceFejlsøgning Problem Mulige årsager LøsningPage LYN MAX 2015, 2011 2016 Drip Stop Calc-Clean Page Page GC2030, 2025 2011 2015 Calc-Clean 4239 000

GC2030 specifications

The Philips GC2030 is a highly efficient steam iron designed to provide exceptional performance and convenience for everyday ironing needs. Known for its innovative features and user-friendly design, this iron stands out in the crowded market of home appliances.

One of the main features of the Philips GC2030 is its powerful steam output. With a continuous steam rate of up to 35 grams per minute, it effortlessly tackles even the toughest creases. Additionally, the iron boasts a steam boost function that delivers up to 130 grams of steam on demand, effectively smoothing out stubborn wrinkles on various fabric types. This makes it an invaluable tool for both quick touch-ups and more intensive ironing tasks.

The GC2030 is equipped with a ceramic soleplate, which ensures smooth gliding over fabrics. The ceramic finish also provides excellent heat distribution, preventing any hot spots that could damage delicate materials. This soleplate design enhances the overall ironing experience, allowing users to maneuver the iron easily across different surfaces.

Another key characteristic of the Philips GC2030 is its lightweight design. Weighing in at just 1.2 kilograms, it is easy to handle, reducing strain during extended ironing sessions. The iron is also ergonomically designed, featuring a comfortable grip that enhances control and precision, making it suitable for users of all ages.

The GC2030 also incorporates innovative technologies to enhance safety and performance. It features an automatic shut-off function that activates when the iron is left unattended, helping to prevent accidents and ensuring peace of mind. Additionally, the iron is designed with a drip-stop system, preventing water leakage during use, which can be a common concern with steam irons.

Furthermore, maintenance is straightforward with the Philips GC2030. It has a large water tank capacity of 300 milliliters, allowing for longer ironing sessions without frequent refilling. The tank is also designed for easy filling under the tap, and the built-in descaling feature helps maintain the iron's performance over time, reducing limescale buildup.

In summary, the Philips GC2030 steam iron combines powerful steam technology, an easy-to-use design, and advanced safety features, making it a top choice for anyone looking to simplify their ironing tasks while achieving excellent results. Whether for everyday clothes or special garments, this iron proves to be both efficient and reliable, ensuring clothes look their best with minimal effort.
Top Page Image Contents