Omega Speaker Systems OS523E, OS532E, OS524E Laser Sighting Status, Calculating Temperature Values

Page 30

Using the Handheld Infrared Thermometer 2

2.3.5 Laser Sighting Status

In the LSR display menu, the status of the laser sighting is shown either as Flashing (FLS) or continuous (on). Pressing the LOCK key will change the status from flashing to continuous and vise versa. There is a slide laser power switch on the left side of the thermometer's case. Set the power switch to ON position, and pull the trigger. The laser beam will turn on (either flashing or continuous depending on the status) as long as the trigger is pulled. Releasing the trigger will automatically turn off the laser beam.

2.3.6 Calculating Temperature Values

The thermometer calculates the MAX, MIN, dIF, and AVG temperatures based on the current temperature.

°F

is the maximum temperature since the temperature measurement session starts (pulling the trigger).

°F

is the minimum temperature since the temperature measurement session starts.

°F

is the difference between the MAX and MIN temperatures.

°F

is the true average temperature since the temperature measurement session starts. The average temperature under continuous operation is accurate for a limited period of time (refer to the specifications). However, the AVG temperature function can be used indefinitely when the thermometer is operating intermittently.

°F

“AVG ---” is displayed when either of the following conditions occur:

1.When the average temperature measurement reaches its time period as stated in the specifications.

2.When the thermometer is trying to measure a target temperature which is outside of its measuring temperature range. At this time the corresponding MAX, MIN, dlF parameters shows _ _ _.

To clear the “AVG ---” display, press the LOCK key to reset or turn off the thermometer.

NOTE

Every time the thermometer goes from the sleep mode to the Real Time mode (by pulling the trigger) or pressing the LOCK key (see Table 2-1) the MAX, MIN, dIF, and AVG values are reset.

2-15

Image 30
Contents User’s Guide Servicing North America Unpacking Instructions Accessories Page Unpacking Instructions Chapter General Description Chapter Digital Video Camera General Description Introduction OS530LE OS530HRE OS530LE-CF OS533E-CF OS534E-CF Features OS523E OS524E Parts of the Thermometer Front of the Thermometer Display Details Key General Description General Description Ac Power Operation Installing the BatteriesOperating the Thermometer Field of View PositionsField of View OS534E, OS523E-1 Field of View OS53xE-CF Field of View OS523E-3 Measurement Techniques 11 Recorder Hookup Real Time Mode Active Operation 12. General Operational Block DiagramReal Time Modes 13. Visual Function Flow Chart Adjusting Emissivity Using the Lock FunctionUsing the Trigger Function Using the Distance Function Must be hard, flat, and reflective to ultrasonic pulseDS = 17. Field of View of Distance Meter HH-DM Calculating Temperature Values Laser Sighting StatusChanging the Temperature from F to C or vice Versa Turning on the Display BacklightingThermocouple Input OS532E, OS533E, OS534E Using the Alarm Functions To set the low alarm value OS533E, OS534E, OS523E, OS524E Use the Ambient Target Temperature Compensation MB RAM Sending temperature data to PC in Real Time Download Stored Temperature data to PC Communicating through Hyper terminalMenu Description Using the Handheld Infrared Thermometer PC Interface Commands AsciiString Description Storing Temperature Data on Command OS534E, OS523E, OS524E Logging Temperature Data in Real Time OS523E, OS524E,OS534E Erasing the Temperature Data from Memory Recall Mode Passive Operation ModeRecall Modes Reviewing the Last Parameters Laser Sighting Description Right Side ViewTwo Laser Configurations Operating the Laser SightingLines of Sight of the Laser Sighting and Thermometer Installing and Operating the Sighting Scope Sighting ScopeInstalling the Sighting Scope Turning Camera ON/OFF Battery InstallationDigital Video Camera Camera Parts Menu SelectionDigital Video Camera Safety Warning Maintenance Replacing the BatteriesCleaning the Lens Calibrating the ThermometerServicing the Laser Sighting Troubleshooting Guide Problem SolutionTroubleshooting Guide Problem Troubleshooting Guide Specifications are for all models except where noted SpecificationsGND With Built-in Distance Module Laser Sighting Digital Video Camera Specifications Glossary of Key Strokes Glossary of Key Strokes Thermal Radiation Appendix How Infrared Thermometry Works aBlackbody Calculating Temperature Optics Field of View Metals Appendix Emissivity ValuesNonmetals Appendix Determining an Unknown Emissivity Figure C-1. Determining Emissivity Figure C-2. Determining Emissivity with a Drilled Hole Appendix Determining an Unknown Emissivity Index Field of View Diagrams Recall WARRANTY/DISCLAIMER Shop online at omega.com PH/CONDUCTIVITY