Invacare 1163197 manual Adjusting Footplate Height, Raising/Lowering Elevating Legrest Assembly

Page 21

SECTION 4—FRONT RIGGINGS

Adjusting Footplate Height

NOTE: For this procedure, refer to FIGURE 4.2 on page 21.

NOTE: This procedure applies to the swingaway front riggings and swingaway elevating legrest.

1.Remove the front rigging assembly. Refer to Installing/Removing Front Riggings Assembly on page 20.

2.Pull the cam lock lever down to unlocked position.

NOTE: The elevating legrest has two sets of release buttons, one set above the other. Each set will be visible one at a time allowing finer footplate height adjustment.

3.Push in the spring buttons and reposition the footplate assembly to the desired height.

4.Ensure that the spring buttons fully protrude from adjustment holes on both sides of the front rigging support.

5.Rotate cam lock lever up to the locked position.

6.Reinstall the swingaway front rigging assembly. Refer to Installing/Removing Front Riggings Assembly on page 20.

Front Rigging Support

Spring Buttons (Located on both sides of each front rigging support)

Adjustment

Holes

Cam Lock Lever (Shown

in Locked Position)

FIGURE 4.2 Adjusting Footplate Height

Raising/Lowering Elevating Legrest Assembly

NOTE: For this procedure, refer to FIGURE 4.3.

WARNING

Ensure hands and fingers are clear of elevating legrest mechanism before pushing release lever to lower the elevating legrest. Otherwise injury may occur due to pinch points.

The user’s leg MUST be supported by an assistant before attempting to lower legrest.

NOTE: For this procedure, refer to FIGURE 4.3 on page 21.

1. To raise the elevating legrest, the assistant should hold

Release Lever

the support tube and raise the elevating legrest until the

 

desired height is obtained.

 

2. To lower the elevating legrest, perform the following: A. Support user leg with one hand.

B. Push release lever downward with other hand.

C. Gently, lower user leg down and rest against the legrest.

Support Tube

FIGURE 4.3 Raising/Lowering Elevating Legrest

Assembly

Part No. 1163197

21

Insignia™

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Insignia Insignia Table of Contents Wheel Locks Wheelchair TIE-DOWN Restraints and Seat Positioning Straps Special NotesLabel Location Insignia Typical Product ParametersGeneral Guidelines Weight Training/Weight LimitationStability All Models Anti-TippersOperating Information General Guidelines Safety/Handling of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance Coping With Everyday ObstaclesReaching, Leaning Backwards Reaching, Leaning and Bending ForwardMethod 1 Wheelchair With Step Tubes TippingStairways StairwaysEscalators Transferring To and From Other SeatsUnfolding and Folding Wheelchair Folding Hammock or Sling Seat Models Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGInspect/Adjust Monthly TroubleshootingMaintenance Front Riggings Installing/Removing Front Riggings AssemblyRaising/Lowering Elevating Legrest Assembly Adjusting Footplate HeightReplacing Heel Loop Replacing Heel LoopRemoving/Installing the Armrest Adjusting Armrest HeightArms Removing/Installing the Flip Back Arm Using Flip Back ArmrestReplacing Clothing Guards Removing/Installing the Flip Back ArmPosition for Desk Length Removing/Installing the Seat Upholstery Removing/Installing the Seat CushionSeat and Back Removing/Installing the Seat Cushion Removing/Installing the Back UpholsteryAdjusting Seat Width Adjusting Back Height, Back Angle or Seat DepthRear Wheels Removing/Installing Rear WheelsRemoving/Installing Rear Wheels Removing Adjusting Quick-Release AxleReplacing Rear Wheel Handrim Replacing/Repairing Rear Wheel TireRemoving/Installing Front Casters Removing/Installing the Caster/Fork/Headtube AssemblyFront Casters Removing/Installing the Caster/Fork/Headtube Assembly Adjusting Front Caster Mounting Replacing/Repairing Front Caster Tire/TubeWheel Locks Using Patient Operated Wheel LocksAdjusting Patient-Operated Wheel Locks ANTI-TIPPERS Installing/Adjusting Anti-tippersChanging Orientation of Anti-Tip Wheels Installing Anti-TippersAdjusting Anti-Tippers Installing/Removing the I.V. Holder Adjusting the Height of the I.V. HolderOptions Installing/Removing the O2 Holder Installing/Removing the O2 Holder Cleaning the O2 Holder Using the O2 HolderBottom View of IV/O2 Holder with ANTI-TIPPER Installed Installing/Removing the IV/O2 HolderDetail C Detail D Bottom View Using the IV/O2 HolderCleaning the IV/O2 Holder Adjusting the Height of the IV PoleInstalling/Removing the Seat Positioning Strap Installing Crutch and Cane CarrierInstalling/Removing the Seat Positioning Strap Options Limited Warranty USA

1163197 specifications

The Invacare 1163197 is a standout product in the realm of mobility aids, specifically designed to enhance the quality of life for individuals with limited mobility. This model integrates advanced technology and user-friendly features that provide both comfort and safety.

One of the main characteristics of the Invacare 1163197 is its robust construction. Built to withstand daily use, the frame is crafted from durable materials ensuring longevity and stability. The design incorporates a lightweight aluminum structure, making it easy to maneuver while maintaining strength. The weight capacity of the unit is impressive, accommodating users up to a certain threshold.

Comfort is paramount in the design of the Invacare 1163197. The seat is padded with high-density foam, providing exceptional support and cushioning. Furthermore, the seat height is adjustable, allowing users to find their ideal position for both comfort and accessibility. This feature is particularly beneficial for individuals who may require the aid of caregivers or family members to assist with transfers.

The Invacare 1163197 also excels in terms of mobility and maneuverability. It is equipped with large swivel wheels that facilitate easy navigation over various terrains, whether indoors or outdoors. The front wheels can pivot 360 degrees, allowing for tight turns and improved control, making it suitable for crowded spaces or narrow hallways.

Safety features are a highlight of this mobility aid. The model includes reliable braking systems, providing users with a sense of security while stationary. Handgrips are ergonomically designed, reducing strain on the hands and allowing for easy operation when moving the chair.

In addition to its physical attributes, the Invacare 1163197 is designed with portability in mind. It can be easily folded for transport or storage, making it ideal for travel. The streamlined design ensures that it can fit into most vehicles with ease.

Finally, the aesthetic appeal of the Invacare 1163197 should not be overlooked. The sleek design, combined with a variety of color options, allows users to choose a model that reflects their personal style while also fulfilling their mobility needs.

In summary, the Invacare 1163197 is a well-rounded mobility aid that emphasizes comfort, safety, and practicality, making it an excellent choice for those seeking to enhance their independence and mobility.
Top Page Image Contents