Invacare 1163197 manual Installing/Removing the IV/O2 Holder

Page 45

SECTION 11—OPTIONS

Installing/Removing the IV/O2 Holder

CAUTION

The IV/O2 holder can only be installed on the left side due to the angle of the plate between the step tube and the IV/O2 holder frame. Installation of the IV/O2 holder on the right side cannot be achieved due to interference of the IV/O2 holder with the back upholstery.

NOTE: Right and left are determined by the sitting in the wheelchair.

Installing

NOTE: For this procedure, refer to FIGURE 11.4 and FIGURE 11.5 on page 46.

1.Remove the left anti‐tipper. Refer to Installing/Adjusting Anti‐tippers on page 37 of the owner’s manual, p/n 1163197.

2.Insert the anti‐tipper into the IV/O2 holder mounting tube until the release button is visible through the opening in the bottom of the IV/O2 holder mounting tube (FIGURE 11.4).

IV/O2 Holder

IV/O2 Holder

Mounting Tube

BOTTOM VIEW OF IV/O2

HOLDER WITH ANTI-TIPPER

INSTALLED

Release Button

Anti-Tipper

FIGURE 11.4 Installing Anti-Tipper into IV/O2 Holder Mounting Tube

NOTE: When performing STEP 3, the IV/O2 holder mounting tube will slide over top of the step tube while the anti‐tipper will slide inside the step tube.

3.Slide the IV/O2 holder and anti‐tipper assembly onto the step tube and, while pressing the release button, insert the anti‐tipper into the step tube (Detail “A” and “D” in FIGURE 11.5).

4.Ensure the release button locks in the hole on the bottom of the step tube (Detail “A” and “D” in FIGURE 11.5). NOTE: Mounting bracket of IV/O2 holder should be positioned between the two axle mounting positions on vertical frame tube.

5.Secure mounting bracket and support block against vertical frame tube with mounting screw (Detail “A” and “B” in FIGURE 11.5). Tighten securely.

6.Remove the top mounting screw that secures the back upholstery to the back cane (Detail “A” in FIGURE 11.5).

7.Secure the upper mounting bracket of the IV/O2 holder and back upholstery to the back cane with the mounting screw removed in STEP 6. Tighten securely (Detail “C” in FIGURE 11.5).

Removing

NOTE: For this procedure, refer to FIGURE 11.5.

1.Press the release button in and remove the anti‐tipper (Detail “D”).

2.Remove the mounting screw that secures the mounting bracket and support block against vertical frame tube (Detail “A” and “B”).

3.Remove the top mounting screw that secures the IV/O2 holder and back upholstery to the back cane (Detail “C”).

4.Remove the mounting tube of the IV/O2 holder off of the step tube (Detail “A”).

5.Install the anti‐ tipper. Refer to Installing/Adjusting Anti‐tippers on page 37 of the owner’s manual, p/n 1163197.

6.Secure the back upholstery to the back cane with the mounting screw removed in STEP 2 (Detail “C”).

Part No. 1163197

45

Insignia™

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Insignia Insignia Table of Contents Wheel Locks Wheelchair TIE-DOWN Restraints and Seat Positioning Straps Special NotesLabel Location Insignia Typical Product ParametersGeneral Guidelines Weight Training/Weight LimitationStability All Models Anti-TippersOperating Information General Guidelines Safety/Handling of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance Coping With Everyday ObstaclesReaching, Leaning Backwards Reaching, Leaning and Bending ForwardMethod 1 Wheelchair With Step Tubes TippingStairways StairwaysEscalators Transferring To and From Other SeatsUnfolding and Folding Wheelchair Folding Hammock or Sling Seat Models Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGInspect/Adjust Monthly TroubleshootingMaintenance Front Riggings Installing/Removing Front Riggings AssemblyRaising/Lowering Elevating Legrest Assembly Adjusting Footplate HeightReplacing Heel Loop Replacing Heel LoopRemoving/Installing the Armrest Adjusting Armrest HeightArms Removing/Installing the Flip Back Arm Using Flip Back ArmrestReplacing Clothing Guards Removing/Installing the Flip Back ArmPosition for Desk Length Removing/Installing the Seat Upholstery Removing/Installing the Seat CushionSeat and Back Removing/Installing the Seat Cushion Removing/Installing the Back UpholsteryAdjusting Seat Width Adjusting Back Height, Back Angle or Seat DepthRear Wheels Removing/Installing Rear WheelsRemoving/Installing Rear Wheels Removing Adjusting Quick-Release AxleReplacing Rear Wheel Handrim Replacing/Repairing Rear Wheel TireRemoving/Installing Front Casters Removing/Installing the Caster/Fork/Headtube AssemblyFront Casters Removing/Installing the Caster/Fork/Headtube Assembly Adjusting Front Caster Mounting Replacing/Repairing Front Caster Tire/TubeWheel Locks Using Patient Operated Wheel LocksAdjusting Patient-Operated Wheel Locks ANTI-TIPPERS Installing/Adjusting Anti-tippersChanging Orientation of Anti-Tip Wheels Installing Anti-TippersAdjusting Anti-Tippers Installing/Removing the I.V. Holder Adjusting the Height of the I.V. HolderOptions Installing/Removing the O2 Holder Installing/Removing the O2 Holder Cleaning the O2 Holder Using the O2 HolderBottom View of IV/O2 Holder with ANTI-TIPPER Installed Installing/Removing the IV/O2 HolderDetail C Detail D Bottom View Using the IV/O2 HolderCleaning the IV/O2 Holder Adjusting the Height of the IV PoleInstalling/Removing the Seat Positioning Strap Installing Crutch and Cane CarrierInstalling/Removing the Seat Positioning Strap Options Limited Warranty USA

1163197 specifications

The Invacare 1163197 is a standout product in the realm of mobility aids, specifically designed to enhance the quality of life for individuals with limited mobility. This model integrates advanced technology and user-friendly features that provide both comfort and safety.

One of the main characteristics of the Invacare 1163197 is its robust construction. Built to withstand daily use, the frame is crafted from durable materials ensuring longevity and stability. The design incorporates a lightweight aluminum structure, making it easy to maneuver while maintaining strength. The weight capacity of the unit is impressive, accommodating users up to a certain threshold.

Comfort is paramount in the design of the Invacare 1163197. The seat is padded with high-density foam, providing exceptional support and cushioning. Furthermore, the seat height is adjustable, allowing users to find their ideal position for both comfort and accessibility. This feature is particularly beneficial for individuals who may require the aid of caregivers or family members to assist with transfers.

The Invacare 1163197 also excels in terms of mobility and maneuverability. It is equipped with large swivel wheels that facilitate easy navigation over various terrains, whether indoors or outdoors. The front wheels can pivot 360 degrees, allowing for tight turns and improved control, making it suitable for crowded spaces or narrow hallways.

Safety features are a highlight of this mobility aid. The model includes reliable braking systems, providing users with a sense of security while stationary. Handgrips are ergonomically designed, reducing strain on the hands and allowing for easy operation when moving the chair.

In addition to its physical attributes, the Invacare 1163197 is designed with portability in mind. It can be easily folded for transport or storage, making it ideal for travel. The streamlined design ensures that it can fit into most vehicles with ease.

Finally, the aesthetic appeal of the Invacare 1163197 should not be overlooked. The sleek design, combined with a variety of color options, allows users to choose a model that reflects their personal style while also fulfilling their mobility needs.

In summary, the Invacare 1163197 is a well-rounded mobility aid that emphasizes comfort, safety, and practicality, making it an excellent choice for those seeking to enhance their independence and mobility.
Top Page Image Contents