Invacare 1163197 manual Operating Information

Page 9

SECTION 1—GENERAL GUIDELINES

Seat‐to‐floor angle of 0° or 3°: If so equipped, anti‐tippers must be attached at all times. Inasmuch as the anti‐tippers are an option for 0° or 3° on this wheelchair, Invacare strongly recommends using the anti‐tippers as a safeguard for the wheelchair user.

Seat‐to‐floor angle of 6°: If changing the seat‐to‐floor angle to 6°, anti‐tippers must be installed.

ALWAYS use anti‐tippers. When outdoors on wet, soft ground or on gravel surfaces, anti tippers may not provide the same level of protection against tipover. Extra caution MUST be observed when traversing such surfaces.

Operating Information

Unless otherwise noted, all service and adjustment should be performed while the wheelchair is unoccupied.

To determine and establish your particular safety limits, practice bending, reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair.

When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are dry prior to use. Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly. Failure to observe this warning may result in injury to the user or bystanders.

If the wheelchair is exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, prior to use, ensure that the handgrips DO NOT twist on the handle. Otherwise, damage or injury may occur.

DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H‐blocks.

Avoid storing or using the wheelchair near open flame or combustible products. Serious injury or damage to property may result.

DO NOT traverse, climb or go down ramps or slopes greater than 9°.

DO NOT attempt to move up or down an incline with a water, ice or oil film.

DO NOT operate on roads, streets or highways.

DO NOT attempt to ride over curbs or obstacles. Doing so may cause your wheelchair to tip over and cause bodily harm to you or damage to the wheelchair.

DO NOT attempt to reach objects if you have to move forward in the seat.

DO NOT attempt to reach objects if you have to pick them up from the floor by reaching down between your knees.

DO NOT lean over the top of the back upholstery to reach objects behind you, as this may cause the wheelchair to tip over.

DO NOT shift your weight or sitting position toward direction you are reaching as the wheelchair may tip over.

DO NOT attempt to stop a moving wheelchair with wheel locks. Wheel locks are not brakes. DO NOT tip the wheelchair without assistance.

DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.

Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Turn both casters parallel to the object you are transferring onto. When transferring to and from the wheelchair, ALWAYS engage both wheel locks.

Part No. 1163197

9

Insignia

Image 9
Contents Insignia Insignia Table of Contents Wheel Locks Wheelchair TIE-DOWN Restraints and Seat Positioning Straps Special NotesLabel Location Insignia Typical Product ParametersGeneral Guidelines Weight Training/Weight LimitationStability All Models Anti-TippersOperating Information General Guidelines Safety/Handling of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance Coping With Everyday ObstaclesReaching, Leaning Backwards Reaching, Leaning and Bending ForwardMethod 1 Wheelchair With Step Tubes TippingStairways StairwaysEscalators Transferring To and From Other SeatsUnfolding and Folding Wheelchair Folding Hammock or Sling Seat Models Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGInspect/Adjust Monthly TroubleshootingMaintenance Front Riggings Installing/Removing Front Riggings AssemblyRaising/Lowering Elevating Legrest Assembly Adjusting Footplate HeightReplacing Heel Loop Replacing Heel LoopRemoving/Installing the Armrest Adjusting Armrest HeightArms Removing/Installing the Flip Back Arm Using Flip Back ArmrestReplacing Clothing Guards Removing/Installing the Flip Back ArmPosition for Desk Length Removing/Installing the Seat Upholstery Removing/Installing the Seat CushionSeat and Back Removing/Installing the Seat Cushion Removing/Installing the Back UpholsteryAdjusting Seat Width Adjusting Back Height, Back Angle or Seat DepthRear Wheels Removing/Installing Rear WheelsRemoving/Installing Rear Wheels Removing Adjusting Quick-Release AxleReplacing Rear Wheel Handrim Replacing/Repairing Rear Wheel TireRemoving/Installing Front Casters Removing/Installing the Caster/Fork/Headtube AssemblyFront Casters Removing/Installing the Caster/Fork/Headtube Assembly Adjusting Front Caster Mounting Replacing/Repairing Front Caster Tire/TubeWheel Locks Using Patient Operated Wheel LocksAdjusting Patient-Operated Wheel Locks ANTI-TIPPERS Installing/Adjusting Anti-tippersChanging Orientation of Anti-Tip Wheels Installing Anti-TippersAdjusting Anti-Tippers Installing/Removing the I.V. Holder Adjusting the Height of the I.V. HolderOptions Installing/Removing the O2 Holder Installing/Removing the O2 Holder Cleaning the O2 Holder Using the O2 HolderBottom View of IV/O2 Holder with ANTI-TIPPER Installed Installing/Removing the IV/O2 HolderDetail C Detail D Bottom View Using the IV/O2 HolderCleaning the IV/O2 Holder Adjusting the Height of the IV PoleInstalling/Removing the Seat Positioning Strap Installing Crutch and Cane CarrierInstalling/Removing the Seat Positioning Strap Options Limited Warranty USA

1163197 specifications

The Invacare 1163197 is a standout product in the realm of mobility aids, specifically designed to enhance the quality of life for individuals with limited mobility. This model integrates advanced technology and user-friendly features that provide both comfort and safety.

One of the main characteristics of the Invacare 1163197 is its robust construction. Built to withstand daily use, the frame is crafted from durable materials ensuring longevity and stability. The design incorporates a lightweight aluminum structure, making it easy to maneuver while maintaining strength. The weight capacity of the unit is impressive, accommodating users up to a certain threshold.

Comfort is paramount in the design of the Invacare 1163197. The seat is padded with high-density foam, providing exceptional support and cushioning. Furthermore, the seat height is adjustable, allowing users to find their ideal position for both comfort and accessibility. This feature is particularly beneficial for individuals who may require the aid of caregivers or family members to assist with transfers.

The Invacare 1163197 also excels in terms of mobility and maneuverability. It is equipped with large swivel wheels that facilitate easy navigation over various terrains, whether indoors or outdoors. The front wheels can pivot 360 degrees, allowing for tight turns and improved control, making it suitable for crowded spaces or narrow hallways.

Safety features are a highlight of this mobility aid. The model includes reliable braking systems, providing users with a sense of security while stationary. Handgrips are ergonomically designed, reducing strain on the hands and allowing for easy operation when moving the chair.

In addition to its physical attributes, the Invacare 1163197 is designed with portability in mind. It can be easily folded for transport or storage, making it ideal for travel. The streamlined design ensures that it can fit into most vehicles with ease.

Finally, the aesthetic appeal of the Invacare 1163197 should not be overlooked. The sleek design, combined with a variety of color options, allows users to choose a model that reflects their personal style while also fulfilling their mobility needs.

In summary, the Invacare 1163197 is a well-rounded mobility aid that emphasizes comfort, safety, and practicality, making it an excellent choice for those seeking to enhance their independence and mobility.