Cisco Systems 78-16845-01 manual Prerequisites for Adding ONS 1580x NEs

Page 13

Chapter 3 Building the Network

3.5.1 Prerequisites for Adding NEs

For NEs with OSC, additional configuration is required. Add patches between the Wave and OSC filter interfaces. For example, if the Wave 0 interface is connected physically to the OSC filter 0/0 interface, add a patch using the following command:

patch Wave 0 Oscfilter 0/0

3.5.1.4.5 Unbundled CiscoView (Optional)

In CTM, CiscoView is used for configuring and monitoring ONS 155xx NEs. Server-based (unbundled) CiscoView should be installed on the CTM server. Without unbundled CiscoView:

•You cannot launch CiscoView on ONS 15501 NEs.

•You can launch CiscoView on ONS 15530 and ONS 15540 NEs only if embedded CiscoView is installed on these NEs.

For information about installing CiscoView on the CTM server, see the Cisco Transport Manager Release 6.0 Installation Guide.

3.5.1.4.6 Performance Monitoring (Optional)

Performance monitoring is optional, but you must enable it if you want to monitor threshold alarms and performance parameters.

You can enable performance monitoring by using the device CLI or CiscoView.

•For information about using the CLI, see the relevant hardware documentation.

•For information about using CiscoView, see Appendix I, “Using CiscoView to Configure and Monitor ONS 15501, ONS 15530, and ONS 15540 NEs.”

3.5.1.5Prerequisites for Adding ONS 1580x NEs

Before adding ONS 1580x NEs to CTM, complete the following prerequisites:

•For the ONS 15800, position the master Control and Monitoring Processor (CMP), named CTM-W or CMP-W-2E, in the physical location 01-01-15.

•For the ONS 15801 and ONS 15808, position the master CMP (named CTM-W or CMP-W-2E) in the physical location 01-01-13.

•For the ONS 15800, ONS 15801 and ONS 15808, the server must be able to Telnet to port 1000 on the NEs. The network configuration must enable connectivity between the server machine and the ports on each managed NE.

3.5.1.6Prerequisites for Adding Cisco CRS-1 and XR 12000 NEs

Before adding a Cisco Carrier Routing System 1 (CRS-1) or XR 12000 NE to CTM, complete the following prerequisites:

•Enter the following CLI command to add the Manageability pie (if it is not already installed):

install add <PIE_file_location> to <device> activate

• Enter the following CLI commands:

 

 

xml agent corba (to connect using CORBA)

 

 

xml agent corba ssl (to connect in secure mode using SSL)

 

 

domain ipv4 host <EMS_server_name> <EMS_server_IP_address>

 

 

logging events level informational

 

 

Cisco Transport Manager Release 6.0 User Guide

 

 

 

 

 

 

78-16845-01

 

 

3-13

 

 

 

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Overview Building the NetworkAdding Groups How Do I Build Groups?Copying Groups Field DescriptionDeleting Groups Moving GroupsDeleting a Single Group Adding Network Partitions How Do I Build Network Partitions?Deleting Multiple Groups Deleting Network Partitions Modifying Network PartitionsAdding Subnetworks How Do I Build Subnetworks?Moving Subnetworks How Do I Build NEs?Deleting Subnetworks Prerequisites for Adding ONS 15216 EDFA2 or EDFA3 NEs Prerequisites for Adding NEsPrerequisites for Adding ONS 15302 and ONS 15305 NEs Building the Network Prerequisites for Adding NEs Hostnames and IP Addresses Required An Efficient Network Topology Setup Prerequisites for Adding Cisco CRS-1 and XR 12000 NEs Prerequisites for Adding ONS 1580x NEsPrerequisites for Adding Cisco MGX Voice Gateway Devices Prerequisites for Adding Cisco Catalyst 6509 NEsOption Description Setting Up Nonstandard Community StringsChanging the Service-Level Passwords Using the CLI Adding a Single NE Adding NEsNE ID NE ID- Read-only Adding Multiple NEsField Descriptions for the Add New NE Wizard NE Properties Panel Not selectable if Automatic subnetwork Grouping is enabled Moving an NE from One Group to Another Copying an NE from One Group to AnotherAutomatically Grouping NEs in Subnetworks Moving an NE from One Network Partition to AnotherDeleting a Single NE Deleting NEsDeleting Multiple NEs Removing a Deleted NE Restoring a Deleted NE How Do I Build Links?Searching for an NE Overview of Supported Links ONS 15454 Sonet Layer NE Model NE Card PhysicalOPT-BST ONS 15600 Sonet File Viewing the Link Table10describes the fields in Link table Field Description Filtering Links in the Network Map Filtering the Link TableCreating Links Building the Network Creating Links 12 Field Descriptions for the Create Link Wizard Field Descriptions for the Create Link Wizard Field Modifying LinksLink Type Link Validity Link Color 14 Field Descriptions for the Modify Link Wizard Viewing Link Utilization Deleting LinksColumn Description Filtering the Link Utilization TableCustomizing a Network Map How Do I Use Network Maps?Payload Type Description Click UI Properties Viewing a Node in the Network Map Adjusting the Zoom Level or Pan PositionModifying a Node Icon Modifying a Node Icon or a Map Background ImageModifying a Map Background Saving Changes to the Network Map Discovering ONS 155xx NEs Discovering CTC-Based NEsDiscovery Information Table Time stamp Rediscovering ONS 155xx, CRS-1, and XR 12000 NEsResetting the Resync Interval How Do I Discover the Network for MGX Voice Gateway Devices? Message Quality Description Discovering NEsSetting Up External or Line Timing for CTC-Based Sonet NEs Building the Network Bits 1 OUT Setting Up Internal Timing for CTC-Based Sonet NEsOOS Setting Up External or Line Timing for CTC-Based SDH NEs Unframed , FAS , FAS + CAS Bits 1 OUT Setting Up Internal Timing for CTC-Based SDH NEs Viewing Clocking Sources Displaying the List of Available Clock Sources Configuring Global ClockingDisplaying the List of Manual Clock Sources Creating a Manual Clock Source How Do I Test Connectivity for Optical and Routing Devices?Method Description How Do I Test Connectivity for MGX Voice Gateway Devices? Testing NE ConnectivityPinging an NE Cisco Transport Manager Release 6.0 User Guide 78-16845-01
Related manuals
Manual 138 pages 47.51 Kb
Top Page Image Contents