Cisco Systems 78-16845-01 manual Oos

Page 59

Chapter 3 Building the Network

3.10.1 Synchronization Settings for the ONS 15310, ONS 15327, ONS 15454 SONET, and ONS 15600 SONET

Step 1	Select an ONS 15310, ONS 15327, ONS 15454 SONET, or ONS 15600 SONET NE and choose
	Configuration > NE Explorer.
Step 2	In the node property pane, click the Timing tab. Fields shown depend on the NE that is selected.
Step 3	In the General Timing section of the General subtab, enter the following information:
	•	Timing Mode—Set to External.
	•	SSM Message Set—Set to Generation 1.

•Revertive—Not relevant for internal timing; the default setting (checked) is sufficient.

•Reversion Time—The default setting is sufficient.

• Quality of RES—Set to RES=DUS.

Step 4 In the BITS Facilities section of the General subtab, enter the following information:

•	In State—Set BITS 1 and BITS 2 to	OOS.
•	Out State—Set BITS 1 and BITS 2 to	OOS.

•Coding—Not relevant for internal timing. The default (B8ZS) is sufficient.

•Framing—Not relevant for internal timing. The default (ESF) is sufficient.

•Sync Messaging—Checked.

•AIS Threshold—Not available.

•LBO—Not relevant.

Step 5 In the Reference List subtab, enter the following information:

•NE References

–Ref-1—Set to Internal Clock.

–Ref-2—Set to Internal Clock.

–Ref-3—Set to Internal Clock.

	• BITS 1 Out/BITS 2 Out—Set to None.
Step 6	Click Apply.
Step 7	In the Domain Explorer tree, select the node that will be timed from the node that was set up in
	Steps 1 through 6 and choose Configuration > NE Explorer.
Step 8	In the Timing tab, enter the same information that was entered in Step 3, except for the following:

•In the General Timing section of the General subtab, set the Timing Mode field to Line.

•In the NE References section of the Reference List subtab:

–Ref-1—Set to the OC-N trunk (span) card (non-DWDM node) or OSC card (DWDM) with the closest connection to the node.

–Ref-2—Set to the OC-N trunk (span) card (non-DWDM node) or OSC card (DWDM) with the next closest connection to the node.

–Ref-3—Set to Internal Clock.

Step 9 Click Apply.

Step 10 Repeat Steps 3 through 9 at each node that will be timed by the node.

Cisco Transport Manager Release 6.0 User Guide

	78-16845-01	3-59

Image 59

Contents Overview Building the NetworkField Description How Do I Build Groups?Adding Groups Copying GroupsDeleting a Single Group Moving GroupsDeleting Groups Deleting Multiple Groups How Do I Build Network Partitions?Adding Network Partitions Deleting Network Partitions Modifying Network PartitionsAdding Subnetworks How Do I Build Subnetworks?Deleting Subnetworks How Do I Build NEs?Moving Subnetworks Prerequisites for Adding ONS 15302 and ONS 15305 NEs Prerequisites for Adding NEsPrerequisites for Adding ONS 15216 EDFA2 or EDFA3 NEs Building the Network Prerequisites for Adding NEs Hostnames and IP Addresses Required An Efficient Network Topology Setup Prerequisites for Adding Cisco CRS-1 and XR 12000 NEs Prerequisites for Adding ONS 1580x NEsPrerequisites for Adding Cisco MGX Voice Gateway Devices Prerequisites for Adding Cisco Catalyst 6509 NEsOption Description Setting Up Nonstandard Community StringsChanging the Service-Level Passwords Using the CLI Adding a Single NE Adding NEsNE ID NE ID- Read-only Adding Multiple NEsField Descriptions for the Add New NE Wizard NE Properties Panel Not selectable if Automatic subnetwork Grouping is enabled Moving an NE from One Group to Another Copying an NE from One Group to AnotherAutomatically Grouping NEs in Subnetworks Moving an NE from One Network Partition to AnotherDeleting a Single NE Deleting NEsDeleting Multiple NEs Removing a Deleted NE Searching for an NE How Do I Build Links?Restoring a Deleted NE Overview of Supported Links ONS 15454 Sonet Layer NE Model NE Card PhysicalOPT-BST ONS 15600 Sonet File Viewing the Link Table10describes the fields in Link table Field Description Filtering Links in the Network Map Filtering the Link TableCreating Links Building the Network Creating Links 12 Field Descriptions for the Create Link Wizard Field Descriptions for the Create Link Wizard Link Type Link Validity Link Color Modifying LinksField 14 Field Descriptions for the Modify Link Wizard Viewing Link Utilization Deleting LinksColumn Description Filtering the Link Utilization TablePayload Type Description How Do I Use Network Maps?Customizing a Network Map Click UI Properties Viewing a Node in the Network Map Adjusting the Zoom Level or Pan PositionModifying a Map Background Modifying a Node Icon or a Map Background ImageModifying a Node Icon Saving Changes to the Network Map Discovery Information Table Discovering CTC-Based NEsDiscovering ONS 155xx NEs Time stamp Rediscovering ONS 155xx, CRS-1, and XR 12000 NEsResetting the Resync Interval How Do I Discover the Network for MGX Voice Gateway Devices? Message Quality Description Discovering NEsSetting Up External or Line Timing for CTC-Based Sonet NEs Building the Network Bits 1 OUT Setting Up Internal Timing for CTC-Based Sonet NEsOOS Setting Up External or Line Timing for CTC-Based SDH NEs Unframed , FAS , FAS + CAS Bits 1 OUT Setting Up Internal Timing for CTC-Based SDH NEs Viewing Clocking Sources Displaying the List of Manual Clock Sources Configuring Global ClockingDisplaying the List of Available Clock Sources Method Description How Do I Test Connectivity for Optical and Routing Devices?Creating a Manual Clock Source Pinging an NE Testing NE ConnectivityHow Do I Test Connectivity for MGX Voice Gateway Devices? Cisco Transport Manager Release 6.0 User Guide 78-16845-01

Related manuals

Manual 138 pages 47.51 Kb