Lucent Technologies 8405, 8403, 8411, 8434DX, 8410 guide

on, the voice terminal may not have power. In this case, check the connections and then verify that the particular voice terminal is administered on the DEFINITY switch.)

Adjusting the 8405 and 8410 Voice Terminal Desktop Stand

To provide better display visibility on the 8405D, 8405D Plus, and 8410D set, the desktop stand on these terminals can be installed in a high or low position. (When the voice terminal is shipped from the factory, the stand is in the low position.) Figure 5 shows you the set of tabs to use for each position.

NOTE: On the 8411 voice terminal, you can lift the kickstand on the back of the set to provide a better viewing angle of the terminal display.

Check which position (either the position of the desktop stand or the kickstand, according to the type of voice terminal you are using) allows the user the best viewing angle of the display, and then use the following short procedure for installing the desktop stand in the selected position.

To reinstall the desktop stand on the 8405D, 8405D Plus, or 8410D voice terminal for the low or the high position (See Figure 5.)

1.Place the lower desktop stand tab in the appropriate voice terminal tab slot.

2.Slowly lower the desktop stand until the top tab fits into the appropriate tab slot at the top of the voice terminal. You may need to press inward on the top of the desktop stand (see Figure 5) in order for the tab to fit into the slot.

NOTE: As noted before, if you choose to install the desktop stand in the high position, you may need to pass the cords through the long, rectangular opening that surrounds the jacks and then plug the cords into the jacks BEFORE you place the stand on the back of the voice terminal.

8410, 8434DX, 8411, 8403, 8405 specifications

Lucent Technologies 8403 is a significant telecommunications switch that was primarily utilized in the late 1990s and early 2000s. It played a crucial role in the evolution of telecommunication systems, reflecting the rapid advancements in technology during that period. The 8403, part of the Lucent 8400 series, was known for integrating various features and capabilities that were vital for modern telecommunication networks.

One of the standout features of the Lucent 8403 was its advanced switching technology. Utilizing time division switching and digital signal processing, the device was capable of handling a large volume of calls simultaneously while maintaining high-quality voice transmission. This technology enabled efficient routing of calls and minimized the risk of dropped connections, which was a concern in earlier analog systems.

Another significant characteristic of the Lucent 8403 was its support for a wide range of telecommunications protocols. The switch was designed to facilitate both traditional telephone services and emerging digital services, including ISDN and Frame Relay. By accommodating both circuit-switched and packet-switched networks, the 8403 provided flexibility that major telecommunication providers demanded during that transition period.

The 8403 also featured enhanced signaling options, such as Common Channel Signaling System No. 7 (CCSS7), which allowed for improved call setup, control, and management. This feature significantly reduced the time it took to establish a call, thereby improving overall network efficiency.

Scalability was another key characteristic of the Lucent 8403. As telecommunication needs grew, service providers could expand their systems by integrating additional hardware and modules without requiring a complete overhaul of the existing infrastructure. This adaptability was crucial as demand for services fluctuated and as new technologies emerged.

Moreover, the switch was designed with reliability and redundancy features in mind. Its architecture included failover mechanisms that ensured continued operation even in the event of hardware failures. This reliability was essential for operators that required uninterrupted service delivery.

Lastly, the user-friendly interface of the Lucent 8403 provided simplified management and monitoring capabilities. System administrators could easily access performance metrics, troubleshoot issues, and manage configurations, facilitating more efficient maintenance and operations.

In conclusion, the Lucent Technologies 8403 played a transformative role in telecommunications infrastructure during its era. Its blend of advanced switching technology, protocol support, scalability, reliability, and user-friendly management tools made it a foundational component in the evolution of modern telecom networks. As a result, it served as a significant stepping stone toward the complex, integrated systems we see today.