Lucent Technologies 8434DX, 8411, 8410 user manual Removing the Desktop Stand on the 8403, 8405

Page 17

4.Place the voice terminal face down on a flat surface and turn the terminal face down.

5.Remove the desktop stand which is attached to the base of the voice terminal by tabs on the top and back of the stand. See Figure 7.

Press inward on the top of the stand until you can lift the top of the stand out of the tab slot on the voice terminal.

Lift the bottom of the stand out of the lower tab slot(s).

FIGURE 7: Removing the Desktop Stand on the 8403, 8405, and 8410

6.Snap the 1-foot line cord into the “LINE” jack in the back of the voice terminal.

7.Pass the 1-foot line cord through the “Y”-shaped cord holder above the “LINE” jack, as shown on the back of the voice terminal in Figure 8. (On some voice terminals, you will need to pass the line cord through the channel located to the right of the “LINE” jack.) Coil any remaining part of the cord and place it in one of the recesses on the back of the voice terminal. (Again, see Figure 8.)

8.Snap one end of the coiled cord into the Handset jack (labeled ), as shown in Figure 8. (On some 8403 voice terminal models, you may need to thread the cord into the channel leading to the side edge of the voice terminal; the handset cord will then lead off the side of the voice terminal.)

WARNING: Do not insert the handset cord into the Adjunct jack. It may cause equipment damage.

9.Snap the free end of the 1-foot line cord into the wall jack.

10.Place the base of the voice terminal on the wall-jack mounting studs, and pull downward until it is secure, as shown in Figure 8.

10

Image 17
Contents 8400-Series Voice Terminals Installation and User’s Manual Do not Discard the Blank Designation Card Important User Safety Instructions Service Important Safety Warnings for Installation Additional Installation Warning Other 8400-SERIES Voice Terminals Documentation Using the RS-232-D Jack and AnalogDistance Limitations Installing Your Voice TerminalAuxiliary Power Desktop Installation General Notes for InstallationPage Routing channel For line cord Analog Adjunct jack RS-232-D jack Line jack Adjunct jack Expansion Handset Module jack Adjusting the 8405 and 8410 Voice Terminal Desktop Stand Adjusting the 8405 and 8410 Desktop Stand To wall-mount the 8403, 8405, and 8410 voice terminals Wall InstallationRemoving the Desktop Stand on the 8403, 8405, Placing the Voice Terminal onto the Wall Jack Mounting Studs Attaching Adjunct Equipment D6AP Important Notes for Using the RS-232-D Jack and Analog Adjunct Jack onTo connect your 8411 to the PassageWay PC To connect an Analog Adjunct toLocation of Buttons #9 and #10 on PassageWay and Analog Adjunct Status Indications onPassageWay Status PassageWay Status IndicationsGreen Light Red LightFor the 8405, 8410, and the 8411 Voice Terminals Labeling the Designation CardFor the 8403 Voice Terminal To label the designation card How to Label the Blank Designation CardFor the 8434DX Voice Terminal Programming Options on the 8411 Voice Terminal While on-hook, press Current setting Enable T/R Status Lamps or Other 8400-SERIES Voice Terminals Documentation Voice Terminal Quick Reference Guide Definity Communications System Generic 2 and System
Related manuals
Manual 10 pages 40.06 Kb Manual 10 pages 10.87 Kb Manual 59 pages 21.58 Kb Manual 33 pages 12.06 Kb Manual 33 pages 60.25 Kb Manual 10 pages 42.22 Kb Manual 57 pages 63.59 Kb

8410, 8434DX, 8411, 8403, 8405 specifications

Lucent Technologies 8403 is a significant telecommunications switch that was primarily utilized in the late 1990s and early 2000s. It played a crucial role in the evolution of telecommunication systems, reflecting the rapid advancements in technology during that period. The 8403, part of the Lucent 8400 series, was known for integrating various features and capabilities that were vital for modern telecommunication networks.

One of the standout features of the Lucent 8403 was its advanced switching technology. Utilizing time division switching and digital signal processing, the device was capable of handling a large volume of calls simultaneously while maintaining high-quality voice transmission. This technology enabled efficient routing of calls and minimized the risk of dropped connections, which was a concern in earlier analog systems.

Another significant characteristic of the Lucent 8403 was its support for a wide range of telecommunications protocols. The switch was designed to facilitate both traditional telephone services and emerging digital services, including ISDN and Frame Relay. By accommodating both circuit-switched and packet-switched networks, the 8403 provided flexibility that major telecommunication providers demanded during that transition period.

The 8403 also featured enhanced signaling options, such as Common Channel Signaling System No. 7 (CCSS7), which allowed for improved call setup, control, and management. This feature significantly reduced the time it took to establish a call, thereby improving overall network efficiency.

Scalability was another key characteristic of the Lucent 8403. As telecommunication needs grew, service providers could expand their systems by integrating additional hardware and modules without requiring a complete overhaul of the existing infrastructure. This adaptability was crucial as demand for services fluctuated and as new technologies emerged.

Moreover, the switch was designed with reliability and redundancy features in mind. Its architecture included failover mechanisms that ensured continued operation even in the event of hardware failures. This reliability was essential for operators that required uninterrupted service delivery.

Lastly, the user-friendly interface of the Lucent 8403 provided simplified management and monitoring capabilities. System administrators could easily access performance metrics, troubleshoot issues, and manage configurations, facilitating more efficient maintenance and operations.

In conclusion, the Lucent Technologies 8403 played a transformative role in telecommunications infrastructure during its era. Its blend of advanced switching technology, protocol support, scalability, reliability, and user-friendly management tools made it a foundational component in the evolution of modern telecom networks. As a result, it served as a significant stepping stone toward the complex, integrated systems we see today.