Lucent Technologies 8405, 8403, 8411, 8434DX General Notes for Installation, Desktop Installation

Page 9

1145B1 Bulk Power Supply (PEC: 2404-010)

Battery for the 1145B1 (2 amp battery = PEC: 24700;

or 5 amp battery = PEC: 24701)

KS-22911 L2 (replaced by the MSP-1 Power Supply and 1151A1/A2 Power Supplies) — This power supply cannot be used with the 8411.

NOTES: The MSP-1, the 1151A1 and A2, and the 1145B are global power supplies.

It is recommended that the 1145A and the 1145B Bulk Power Supplies be used as auxiliary power for the 8434DX voice terminal. These power supplies provide battery back-up, and therefore when power outages occur, the 8434DX display will continue to operate.

If an 8434DX voice terminal with attached adjunct equipment is connected to an expansion module, it should be locally powered by an MSP-1 or an 1151A1 or A2. If this configuration is closet powered by an 1145A, two ports must be used. A KS- 22911 L2 cannot be used in this situation.

General Notes for Installation

Regardless of which configuration is in use, ALL wiring between the PBX and the terminal MUST consist of twisted-pairs, including the modular line cord. The line cord must be a D8W, which consists of four twisted-pairs, or a Lucent Technologies approved equivalent.

Twisted-pair wiring is used to make lines less sensitive to crosstalk. Therefore, failure to use twisted pair wiring may result in less-than-optimum performance of the terminal and may also contribute to problems with the line.

An 8-wire modular cord MUST be used for all 4-wire and any 2-wire installations requiring auxiliary power.

You do NOT need to change any settings on the voice terminal for 2-wire or 4-wire installations. The voice terminal is able to detect whether it is in a

2-wire or a 4-wire configuration.

Desktop Installation

The following instructions are for a desktop installation. If you are mounting the voice terminal on the wall, proceed to the next section, “Wall Installation.”

NOTE: During the desktop installation procedure, refer to Figures 1, 2, 3, and 4 for the location of the jacks referred to in the following steps.

Figure 1 shows the back of one of the 8403 voice terminal models. (Use this figure for installing the 8403, 8405, and 8410. However, note that the location of the jacks on the back of your voice terminal may differ slightly.)

Figure 2 shows the back of the 8411 voice terminal, and Figure 3 shows the

two jacks on the rear of the 8411. Use the RS-232-D jack for connecting a PC dedicated to PassageWay® Solution software and the Analog Adjunct

2

Image 9
Contents 8400-Series Voice Terminals Installation and User’s Manual Do not Discard the Blank Designation Card Important User Safety Instructions Service Important Safety Warnings for Installation Additional Installation Warning Other 8400-SERIES Voice Terminals Documentation Using the RS-232-D Jack and AnalogInstalling Your Voice Terminal Auxiliary PowerDistance Limitations Desktop Installation General Notes for InstallationPage Routing channel For line cord Analog Adjunct jack RS-232-D jack Line jack Adjunct jack Expansion Handset Module jack Adjusting the 8405 and 8410 Voice Terminal Desktop Stand Adjusting the 8405 and 8410 Desktop Stand To wall-mount the 8403, 8405, and 8410 voice terminals Wall InstallationRemoving the Desktop Stand on the 8403, 8405, Placing the Voice Terminal onto the Wall Jack Mounting Studs Attaching Adjunct Equipment D6AP Important Notes for Using the RS-232-D Jack and Analog Adjunct Jack onTo connect your 8411 to the PassageWay PC To connect an Analog Adjunct toLocation of Buttons #9 and #10 on PassageWay and Analog Adjunct Status Indications onPassageWay Status PassageWay Status IndicationsGreen Light Red LightLabeling the Designation Card For the 8403 Voice TerminalFor the 8405, 8410, and the 8411 Voice Terminals How to Label the Blank Designation Card For the 8434DX Voice TerminalTo label the designation card Programming Options on the 8411 Voice Terminal While on-hook, press Current setting Enable T/R Status Lamps or Other 8400-SERIES Voice Terminals Documentation Voice Terminal Quick Reference Guide Definity Communications System Generic 2 and System
Related manuals
Manual 10 pages 40.06 Kb Manual 10 pages 10.87 Kb Manual 59 pages 21.58 Kb Manual 33 pages 12.06 Kb Manual 33 pages 60.25 Kb Manual 10 pages 42.22 Kb Manual 57 pages 63.59 Kb

8410, 8434DX, 8411, 8403, 8405 specifications

Lucent Technologies 8403 is a significant telecommunications switch that was primarily utilized in the late 1990s and early 2000s. It played a crucial role in the evolution of telecommunication systems, reflecting the rapid advancements in technology during that period. The 8403, part of the Lucent 8400 series, was known for integrating various features and capabilities that were vital for modern telecommunication networks.

One of the standout features of the Lucent 8403 was its advanced switching technology. Utilizing time division switching and digital signal processing, the device was capable of handling a large volume of calls simultaneously while maintaining high-quality voice transmission. This technology enabled efficient routing of calls and minimized the risk of dropped connections, which was a concern in earlier analog systems.

Another significant characteristic of the Lucent 8403 was its support for a wide range of telecommunications protocols. The switch was designed to facilitate both traditional telephone services and emerging digital services, including ISDN and Frame Relay. By accommodating both circuit-switched and packet-switched networks, the 8403 provided flexibility that major telecommunication providers demanded during that transition period.

The 8403 also featured enhanced signaling options, such as Common Channel Signaling System No. 7 (CCSS7), which allowed for improved call setup, control, and management. This feature significantly reduced the time it took to establish a call, thereby improving overall network efficiency.

Scalability was another key characteristic of the Lucent 8403. As telecommunication needs grew, service providers could expand their systems by integrating additional hardware and modules without requiring a complete overhaul of the existing infrastructure. This adaptability was crucial as demand for services fluctuated and as new technologies emerged.

Moreover, the switch was designed with reliability and redundancy features in mind. Its architecture included failover mechanisms that ensured continued operation even in the event of hardware failures. This reliability was essential for operators that required uninterrupted service delivery.

Lastly, the user-friendly interface of the Lucent 8403 provided simplified management and monitoring capabilities. System administrators could easily access performance metrics, troubleshoot issues, and manage configurations, facilitating more efficient maintenance and operations.

In conclusion, the Lucent Technologies 8403 played a transformative role in telecommunications infrastructure during its era. Its blend of advanced switching technology, protocol support, scalability, reliability, and user-friendly management tools made it a foundational component in the evolution of modern telecom networks. As a result, it served as a significant stepping stone toward the complex, integrated systems we see today.