Lucent Technologies 7400B manual Telephone SW1-1, Factory-default, Data Metering SW1-5

Page 19

CHAPTER 2: INSTALLATION	DEFINITY Communications System
	7400B Data Module
Page 2-8	User’s Guide

Setting the Hardware Three hardware options are selected by setting switches on an internal

Option DIP Switches 8-position DIP switch. Setting these switches is described in the following paragraph; however, for more information about using these options, refer to Chapter 4, “Operation and Configuration.”

Note: The factory-default settings of these switches are correct for the vast majority of applications. Check the default settings shown in Table 2-1 to determine whether you need to make any changes.

Telephone	SW1-1

Without Phone	ON
With Phone	OFF
(factory-default)
Data Metering	SW1-5

On—enabled	ON
Off—disabled	OFF
(factory-default)

Busy Out on Local Loop	SW1-8

On—enabled	ON
Off—disabled	OFF
(factory-default)

TABLE 2-1 Option DIP Switch Settings

Image 19

Contents AT&T 7400B Data Module To Order Copies of this Manual Contents Preface about this Guide 1C-1C-2C-5C-8 Guide TypographicalConventions Organization of thisRelated Troubleshooting. Describes procedures forAppendix C Application Notes. Contains notes on how to Appendix D Quick-Reference Summaries. Contains quickIntroduction Front Panel External FeaturesFront Panel LED Indicator Descriptions Connector DescriptionRear Panel Rear Panel Connector DescriptionsPower Supply Unit Software HardwareRequirements Typical Standalone Installation Typical Installation with Telephone Installation Installation With/Without Telephone Option SW1-1 Selecting DIP-Switch OptionsData Metering Option SW1-5 InstallationMake Busy on Local Loop Option SW1-8 Data Metering SW1-5 Factory-defaultOption DIP Switch Settings Telephone SW1-1Accessing the Hardware Option Switches Connecting the EIA-232-D Cable Supply Connecting the PowerDedicated Terminal Power-Up Self-TestIf YOU are Using a PC If YOU are Using aData Bits Parity Stop Bits Line or data modeOperating Modes Character FormatsEssential AT Commands AT Command Subset AT Command DescriptionMore Connect AT Command Subset ContdBusy Starting the Session Sample ON-LINE SessionSelection +++ No CarrierConfiguration Parameters Operation and ConfigurationCommand Line Action Command Line Set Up Issuing CommandsCommand Line Prefix Command BufferAts3= ddd Enter Result Codes CommandAcknowledgement Verbose Form Numeric DescriptionMultiple Characters From Data Mode to Command Mode and Back Dialing a NumberFollowing is an example At&z m=nnn...n Enter Commands for Using Stored Telephone NumbersConfiguration Recall ResetRemote Site USE At&f Enter Chapter HOW to USE thisPBX Symptom Problem SolutionCheck Speed LED At&d2 Enter Terminate the local loopback test by typing Atq0 o Enter Atx4 Enter LabelDescription Appendix a AT Command SETContd Escape sequence Immediate None Arguments none CommandAArguments none Registernone Examplea CommandD Command Function Switch hook control Ato Enter Command Function Type Arguments Register Example CommentsAtv Enter A-10 User’s Guide Reset and recall a stored profile Data Carrier Detect DCD options Data Terminal Ready DTR options Arguments none Registernone Example Command&FAt&t3 Enter see comment At&v Enter Registernone Example Command&YAt&z2=555-1212 Enter 055 Description Range Values Comments See Also Storable Register DescriptionStorable Comments From a data terminal Register S6 not used Register S8 not used S9 not used Register S13 not used Register S11 not usedRegister S15 not used Register Description Range Values Storable Comments See AlsoRegister S17 not used Register S19 not used S20 not used Values StorableRange of Values Storable Comments See Also RegisterS21Bits 0 and 1 not used default = 2, see comment Register S24 not used Register S27 not used AT&T 7400B Data Module PC Application Guide, ordering number PBX Application Notes PC Applications GuideSelect Result Messages Configuring the SoftwareProcomm Plus Select Modem OptionsPlacing a Call Select Save Setup OptionsC-4 Disconnecting CallPlacing a Call Directly Relay GoldSelect Call a Host Attmail DirectoryPress Esc to return to the Online menu as shown below Disconnecting a CallSelect the letter next to Hayes Smartmodem all models CrosstalkSelect the baud rate that you will use most often Bye Enter Appendix D QUICK-REFERENCE Summaries Table D-1 AT Command SET Command DescriptionSr=n Table D-1 AT Command SET Contd Table D-2 S-REGISTER Summary Register Description Range/UnitTable D-3 Result Codes ConnectedTable D-4 FACTORY-DEFAULT Configuration Parameter Value AT CommandR e Parameter Value Register Table D-4 FACTORY-DEFAULT Configuration ContdTable D-5 EIA-232-D PIN Assignments Pin Circuit Direction FunctionTable D-6 Ascii Character SET Ascii Control KEY Value CharacterTable D-6 Ascii Character SET Contd Glossary Glossary Script files. See command files Index Data Metering DTE, see Data Terminal Device DTR leadRear panel, 1-4Remote site use AT&T Important Safety Instructions Page Important Installation Safety Instructions