Sennheiser SDC 8000 system manual Configuring the operating mode between booths

Page 87

Configuring the SDC 8000 system

Options

3 Mode between Booth

Mode between Booths Mode = Override

Press ENTER to Save

Options

4 Mode in Booths

Mode in Booths

Mode = Mixed

Press ENTER to Save

language. You then have to configure your system so that it comprises three interpreter booth with two interpreter consoles each.

Configuring the operating mode between booths

To determine whether or not interpreter consoles installed in different booths but configured to the same target language can be simultaneously active:

￿From the central unit’s operating menu, choose “Interpretation”, “Options” and “Mode between Booth” one after the other.

The current mode in shown on the display.

￿Choose the desired mode.

You can choose between the modes “Mixed”, “Override” and “Toggle Override”.

yChoose “Mixed” if interpreters in different booths interpret into the same target language and work in turns.

When two interpreters simultaneously interpret into the same

language, the red signal light ring and the “Microphone active” LED on their consoles light up.

yChoose “Override” if activating an interpreter console in another booth turns off the currently active interpreter console. The interpreter console that was just turned off can only be turned on again if the interpreter console by which it was turned off is deactivated.

yChoose “Toggle Override” if activating an interpreter console in another booth turns off the currently active interpreter console. The interpreter console that was just turned off can be turned on again

any time by pressing the MICRO key .

￿Press the ENTER key to save your setting.

Configuring the operating mode within a booth

To determine whether or not the interpreter consoles installed within a booth can be simultaneously active:

￿From the central unit’s operating menu, choose “Interpretation”, “Options” and “Mode in Booths” one after the other.

The current mode in shown on the display.

￿Choose the desired mode.

You can choose between the modes “Mixed” and “Override”.

yChoose “Mixed” if several interpreters in the same booth interpret into the same language. When two interpreters simultaneously

interpret into the same language, the red signal light ring and the “Microphone active” LED on their consoles light up.

yChoose “Override” if activating another interpreter console within a booth turns off the currently active interpreter console. The interpreter console that was just turned off can only be turned on again, if the interpreter console by which it was turned off is deactivated.

87

Page 86 Page 88
Image 87
Page 86 Page 88
Contents SDC Thank you for choosing Sennheiser Contents Via a PA system Configuring the interpretation system 100 Appendix a Safety information SDC 8000 the digital conference and interpretation system Conference consoles Overview of the components SDC 8000 system$!# Technology used All consoles feature Components of the SDC 8000 system in detailConsoles Interpreter console features SDC 8000 D conference unit SDC 8000 C chairman unit SDC 8000 DC conference unit SDC 8000 CC chairman unit Vote LED SDC 8000 DV conference unitSDC 8000 CV chairman unit Autofloor LED SDC 8000 ID interpreter consoleSDC 8000 CU central unit SDC 8000 AO analog output unit optional System cables Taking the floor / Making a request to speak Direct Access modeOperating the components SDC 8000 system Operating the delegate unitsOperating the components of the SDC 8000 system On your console go off With request mode With Req. No clear modeTurning off the microphone / Cancelling a request to speak Voting Selecting an interpretation channelTurning all active conference consoles off priority Using the chip card slot of a conference consoleOperating the VIP units Operating the chairman unitAssigning a participant the speaking right Starting a voting sessionRequest Operating the interpreter consoles Configuring the B-channel of an interpreter consoleUsing the interpreter console Muting the microphone of the interpreter console Switching between the A-channel and the B-channelAdjusting the volume of the consoles’ built-in loudspeakers Operating the central unitF1, F2 and F3 menu keys Menu operating controlsOperating control Menu level Working with the central unit’s operating menu Structuring the SDC 8000 system Interconnecting the conference/interpreter consolesConnecting cable strings to a central unit Interconnecting up to 10 central unitsExpansion stage 2 one central unit with up to 90 consoles Expansion stage 1 one central unit with up to 15 consolesDetermining maximum cable lengths Calculating the voltage drop on the system cables Structuring an interpretation systemMode between booths Toggle Override Selectable modes between or within interpreter boothsMode between booths Mixed Mode between booths OverrideExample Mode in booths MixedMode in booths Override Auto-floor functionAUTO-FLOOR Connecting external audio sources Using external equipmentStructuring the SDC 8000 system Preparing the SDC 8000 system components for set up Setting up the SDC 8000 systemInterconnecting several central units Interconnecting the SDC 8000 system componentsInterconnecting the consoles Connecting a cable string to the central unitTurning the central units on and off Connecting additional equipmentCarrying out remote conferences Pin assignment of the 9-pole sub-D socket AUX OUT Connecting PA systems, recording units, etcDaisy-chaining SDC 8000 AO analog output units Connecting a PC to the central unit Six main menus Configuring the SDC 8000 systemIntroduction to the central unit’s operating menu Start displayEnter Exit Submenus of the Conference menu part 1 Submenus of the Conference menu part 2 Submenus of the Conference menu part 3 Submenus of the Conference menu part 4 Submenus of the Conference menu part 5 Submenus of the Conference menu part 6 Submenus of the Interpretation menu part 1 Submenus of the Interpretation menu part 2 Submenus of the Interpretation menu part 3 Submenus of the Interpretation menu part 4 Submenus of the Interpretation menu part 5 Enter Submenus of the Aux-In/Out menu part 1Submenus of the Aux-In/Out menu part 2 Submenus of the Aux-In/Out menu part 3 Submenus of the Aux-In/Out menu part 4 Submenus of the Aux-In/Out menu part 5 Submenus of the Aux-In/Out menu part 6 Submenus of the System menu part 1 Submenus of the System menu part 2 Submenus of the Language and the License menu part 1 Automatically initializing all conference consoles Settingthe volume of theconsoles’ built-inloudspeakersConfiguring the conference system Turning on the central unit for the first timeManually initializing all conference consoles Reserving a microphone number Selecting a conference mode Setting the speaker limit Resetting the conference system Adjusting the audio settings for the consoles’ microphonesTesting the consoles’ microphones Testing the consoles’ built-in loudspeakersConfiguring the interpretation system Configuring the display of the voting optionsWorking with the interpreter configuration Creating a new interpreter configuration Loading a previously saved interpreter configuration Modifying the currently active interpreter configurationSetting the max. number of interpreter booths/languages Setting the max. number of interpreter consoles per boothOptions Configuring the operating mode within a booth Configuring the operating mode between boothsConfiguring the language options for the interpreter booths Configuring the main target language A-channel of a boothConfiguring the second target language B-channel of a booth Enabling the auto-relay interpretation function Auto-floor ENG To transmit the selected booth number to Adding interpreter consoles to an existing configuration Resetting the interpretation system Configuring the audio inputs and outputs Adjusting the volume of the audio outputsChoosing the audio inputs and outputs Configuring the audio outputs for remote conferencing Assigning a channel to an audio outputTurning the audio inputs or outputs on and off Adjusting the input level of an audio input Adjusting the input sensitivity of an audio inputConfiguring the outputs of the SDC 8000 analog output unit OUT Camera control Configuring connected additional componentsMaking a system diagnosis Checking the communication within a cable stringConfiguring an ambient sound console Choosing the language of the central unit’s operating menu Software, language and licenseDisplaying the central unit’s serial number Conference/interpreter console does not work If problems occurMaintenance and care Replacing a fuseAccessories Specifications SDC 8000 DSDC 8000 C SDC 8000 CC SDC 8000 DCSDC 8000 CV SDC 8000 DVSDC 8000 ID 108 RJ 45 cable SDC 8000 AO analog output unitAppendix a Camera control protocol Syntax of the commandsNotation of the general syntax CommandsAppendix B Control panel protocol Commands113 114 Appendix C Repeater for the SDC 8000 systemApproval 115
Top Page Image Contents