Radio Shack TAD-705 Setting the Dialing Mode, Setting the Ringer, Setting the Display Contrast

Page 9

43-705.fm Page 9 Tuesday, May 23, 2000 8:54 AM

6.Plug the adapter into a standard AC out- let.

SETTING THE DIALING MODE

Set T/P (Tone/Pulse) for the type of service you have. If you are not sure which type you have, do this simple test.

1.Be sure T/P is set to T.

2.Lift the handset and listen for a dial tone.

3.Press any number except 0.

Note: If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not press the access code either.

If the dial tone stops, you have touch- tone service. If the dial tone continues, you have pulse service.

4.If you have pulse service, set T/P to P. Otherwise, leave it set to T.

SETTING THE RINGER

RINGER OFF.LO.HI controls the TAD’s ringer volume. To adjust the ringer volume, set RINGER OFF.LO.HI to HI or LO.

SETTING THE DISPLAY CONTRAST

1.Hold down STOP until the TAD beeps once. 3 and LCD CONTRAST appear. 3 flashes.

2.Repeatedly press :/8 to select the desired display contrast settings.

Note: The TAD has ten (0–9) display contrast settings.

3.Press DIAL to confirm the setting, then press STOP to return to the time display.

SETTING THE LONG

DISTANCE CODE

The Long Distance Code has a default set- ting of 1. You can change the code to “9” if you use a PBX telephone system or “0” if your telephone system requires operator as- sistance to make a long distance call.

Note: If you do not complete each step with- in 8 seconds, the TAD exits setup. Start again at Step 1.

1.Hold down STOP until the TAD beeps once.

2.Press DIAL once. 1 and SET LDS CODE appear. 1 flashes.

3.Repeatedly press :/8 to set the long distance code to 1, 9, or 0.

4.Press DIAL then press STOP to return to the time display.

If you do not want the ringer to sound, set RINGER OFF.LO.HI to OFF. You can still make calls with the ringer off, and you can answer calls if you hear another phone on the same phone line ring or if RING appears on the display.

SETTING THE AREA CODE

Note: If you do not complete each step with- in 8 seconds, the TAD exits setup. Start again at Step 1.

1.Hold down STOP until the TAD beeps once.

Preparation

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 9
Contents TAD-705 Memory Speakerphone Contents Caller ID Operation TroubleshootingImportant Caller ID Information Read this Before InstallationFCC Statement FCC Wants YOU to KnowTelephone Features FeaturesProgrammable Remote Operation Securi Caller ID FeaturesInstalling a Backup Battery PreparationMounting the TAD On a Wall or Wall Plate On a DeskSetting the Ringer Setting the Dialing ModeSetting the Display Contrast Setting the Long Distance CodeSetting the Number of Rings Setting the DAY, Time and DateSwitching Between the Handset and the Speakerphone Adjusting the VolumeTelephone Operation Using Flash Using RedialUsing Hold Using PrivacyStoring Numbers from Caller ID Records Storing a Number in MemoryEntering a Pause A Memory Number Reviewing Memory NumbersTesting Stored Emergency Num- bers Connecting AN Optional HeadsetDialing a Memory Number Chain-DialingTAD Operation Setting the TAD to Answer CallsRecording the Outgoing Messages Checking the Outgoing MessagesIncoming Message Recording Playing MessagesAnnounce Only Recording a Conversation Recording a MemoDeleting Messages Using Call BreakthroughScreening Calls Changing the CBT CodeUsing Remote Commands Using the TOLL-SAVERRemote Command List Changing the Remote Operation Security CodeHave no announcement two Caller ID Operation Reviewing Caller ID Records Caller ID MessagesVIP Call List Deleting Call RecordsUsing Dial Setting the VIP AlertDialing Number Selections Different Area CodeFm Page 25 Tuesday, May 23, 2000 854 AM Problem Suggestion TroubleshootingCare Resetting the TADLimited One-Year Warranty