Radio Shack TAD 1130 Using Flash, Using Redial, Using Mute, Using Tone Services on a Pulse Line

Page 15

43-1130.fm Page 15 Tuesday, May 30, 2000 1:22 PM

Note: If you hear a high-pitched noise from the base’s speaker, the handset and the base are too close together. Move them away from each other.

USING FLASH

FLASH performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting.

For example, if you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press FLASH again to return to the first call.

Note: If you do not have any special phone services, pressing FLASH might disconnect the current call.

USING REDIAL

To quickly dial the last number dialed, lift the handset, press TALK, then press REDIAL.

Notes:

The redial memory holds up to 32 digits, so you can redial long-distance as well as local numbers.

The redial memory also holds pause entries (see “Entering a Pause” on Page 16).

USING MUTE

To talk to someone in the room without the person on the other end of the phone line hearing your conversation, press MUTE. The TALK/LOW BATT indicator flashes.

Press MUTE again to resume your phone conversation.

USING TONE SERVICES ON A PULSE LINE

Some special services, such as bank-by- phone, require tone signals. If you have pulse service, you can still use these special tone services by following these steps.

1.Be sure PULSE-TONEis set to PULSE.

2.Dial the service’s main number.

3.When the service answers, press TONE on the handset. Any additional numbers you dial are sent as tone signals.

When you hang up, the phone automatically resets to pulse dialing.

PAGING

To page the person who has the handset or to locate the handset when the phone is not in use, press PAGE on the base. The handset beeps for 5 seconds. For a longer handset beep, hold down PAGE for at least 5 sec- onds. The handset beeps for 1 minute. To stop it from beeping sooner, press any key on the handset except TALK.

Note: The phone rings if a call comes in dur- ing paging. Press TALK on the handset or SPEAKER on the base to answer the call.

MEMORY DIALING

You can store up to 10 phone numbers in memory, then dial a stored number by enter- ing its memory location number. Each stored number can be up to 20 digits.

Storing a Number in Memory

Notes:

The phone beeps several times and exits the storing process if you wait more than 20 seconds between each key press.

Telephone Operation

15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 15
Contents TAD GHz Digital Spread Spectrum Cordless Speakerphone Contents Troubleshooting Important Safety InstructionsFm Page 4 Tuesday, May 30, 2000 122 PM Battery Safety Instructions Save These Instructions Read this Before InstallationFCC Statement Features FCC Wants YOU to KnowLightning Answering System Features Telephone FeaturesInstallation Mounting the PhoneOn a Desk Top On a Wall Plate or Wall CONNECTING, CHARGING, and Replacing the Battery Pack Installation Quick Look AT the Handset Setting the Dialing ModeTurning the BASE’S Ringer on and OFF Setting the Ringer TONE/VOLUMESetting the Number of Rings Setting the DAY/TIMETelephone Operation Using Tone Services on a Pulse Line Using FlashUsing Redial Using MuteEntering a Pause Using a HeadsetChain-Dialing Service Numbers Testing Stored Emergency Num- bersRECORDING/DELETING AN Outgoing Message Setting the Record TimeTAD Operation Selecting the Outgoing MessageRecording Incoming Messages Setting the TAD to Answer CallsScreening Calls Recording a MemoDeleting Messages Adjusting the TAD’S VolumeSetting the Remote Operation PIN Playing MessagesUsing the TOLL-SAVER Using Remote CommandsRemote Operation Press # Then Remote CommandsProblem Suggestion TroubleshootingCare Limited One-Year Warranty