Radio Shack TAD 1130 owner manual Playing Messages, Adjusting the TAD’S Volume, Deleting Messages

Page 19

43-1130.fm Page 19 Tuesday, May 30, 2000 1:22 PM

To start recording a phone conversation, hold down MEMO on the base until the TAD beeps and ––appears. To stop recording, press PLAY/STOP or MEMO.

The TAD stores a recorded conversation as a message (see “Playing Messages”).

Note: The TAD does not record conversa- tions less than two seconds long, or that use the speakerphone.

PLAYING MESSAGES

After the TAD has recorded a message, the total number of messages stored appears in the message counter window. If you have new messages, the message counter flash- es.

To play your messages, press PLAY/STOP. The TAD announces the number of new and old messages, then plays the new messag- es. The message number appears in the message counter window as each message plays, and the TAD announces the day and time of the call at the end of each message.

To play all messages after playing the new messages, press PLAY/STOP again.

To skip to the next message, press SKIP dur- ing playback.

To replay the current message from the be- ginning, press REPEAT. If you press REPEAT within about 2 seconds after a message be- gins playing, the TAD replays the previous message.

ADJUSTING THE TAD’S VOLUME

To adjust the speaker’s volume, repeatedly press VOLUME 8 or 9 on the base. The volume setting from 1 (lowest) to 10 (high- est) appears in the message counter win- dow.

DELETING MESSAGES

To delete the current message while it is playing, hold down DELETE until the TAD beeps.

To delete all messages at once, while mes- sages are not playing, hold down DELETE on the base until the TAD beeps and 0 appears in the message counter window.

Note: You cannot delete new (unplayed) messages. If you try to delete all messages at once while you still have new messages, the TAD beeps quickly five times and does not delete any messages.

SETTING THE REMOTE OPERATION PIN

The TAD’s two-digit remote operation PIN (personal identification number) prevents un- authorized remote access to your messages. The PIN is preset to 80. Follow these steps to change the PIN to any number from 00 to 99.

Note: If you wait more than 2 minutes be- tween each keypress, the TAD exits the PIN setting process. Start again at Step 1.

1.Hold down PIN until the TAD beeps and 00 appears in the message counter win- dow.

2.Press SKIP to set the first digit of the PIN higher or REPEAT to set it lower. Then press PIN.

3.Press SKIP or REPEAT to set the second digit of the PIN, then press PIN. The TAD announces the new PIN.

To check your PIN at any time, press PIN. The PIN appears in the message counter window, and the TAD announces it.

TAD Operation

19

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 19
Contents TAD GHz Digital Spread Spectrum Cordless Speakerphone Contents Troubleshooting Important Safety InstructionsFm Page 4 Tuesday, May 30, 2000 122 PM Save These Instructions Read this Before Installation Battery Safety InstructionsFCC Statement FCC Wants YOU to Know FeaturesLightning Answering System Features Telephone FeaturesMounting the Phone InstallationOn a Desk Top On a Wall Plate or Wall CONNECTING, CHARGING, and Replacing the Battery Pack Installation Quick Look AT the Handset Setting the Dialing ModeTurning the BASE’S Ringer on and OFF Setting the Ringer TONE/VOLUMESetting the Number of Rings Setting the DAY/TIMETelephone Operation Using Tone Services on a Pulse Line Using FlashUsing Redial Using MuteEntering a Pause Using a HeadsetChain-Dialing Service Numbers Testing Stored Emergency Num- bersRECORDING/DELETING AN Outgoing Message Setting the Record TimeTAD Operation Selecting the Outgoing MessageRecording Incoming Messages Setting the TAD to Answer CallsScreening Calls Recording a MemoDeleting Messages Adjusting the TAD’S VolumeSetting the Remote Operation PIN Playing MessagesUsing Remote Commands Using the TOLL-SAVERRemote Operation Press # Then Remote CommandsProblem Suggestion TroubleshootingCare Limited One-Year Warranty