Radio Shack 900 MHz Switching Between the Handset and Speakerphone, Using Flash, Using Redial

Page 16

43-749.fm Page 16 Tuesday, September 5, 2000 11:24 AM

SWITCHING BETWEEN THE HANDSET AND SPEAKERPHONE

To switch to the speakerphone while you are using the handset, press SPEAKER on the base. When you hear the conversation on the speakerphone, press TALK on the hand- set.

To switch to the handset while you are using the speakerphone, lift the handset off the base. If the handset is away from the base, press TALK, then press SPEAKER.

USING BOTH THE HANDSET AND SPEAKERPHONE

If someone else is using the speakerphone, press TALK on the handset to join the con- versation. If someone else is using the hand- set, press SPEAKER on the base to join the conversation.

During the call, one person can hang up and let the call continue at the other keypad. Or, both people can hang up to end the call.

Note: If you hear a high-pitched noise from the base’s speaker, the handset and the base are too close together.

USING FLASH

FLASH performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting.

For example, if you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press FLASH again to return to the first call.

Note: If you do not have any special phone services, pressing FLASH might disconnect the current call.

FLASH

REDIAL/

PAUSE

USING REDIAL

To quickly dial any of the last three numbers dialed, lift the handset and repeatedly press REDIAL/PAUSE until the desired number ap- pears on the display, then press TALK.

Notes:

The redial memory holds up to 32 digits, so you can redial long-distance as well as local numbers.

The redial memory also holds pause entries (see “Entering a Pause” on Page 19).

USING TONE SERVICES ON A PULSE LINE

Some special services, such as bank-by- phone, require tone signals. If you have pulse service, you can still use these special tone services by following these steps.

1.Be sure DIAL MODE is set to P.

2.Dial the service’s main number. When the service answers, press TONE () on the handset. Any additional numbers you dial are sent as tone signals. When you hang up, the phone automatically resets to pulse dialing.

16

Telephone Operation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 16
Contents MHz Digital Spread Spectrum Digital Answering System Contents Answering System Operation Features Telephone FeaturesRead this Before Installation Answering System FeaturesImportant Caller ID Information Important Safety Instructions FCC StatementFm Page 7 Tuesday, September 5, 2000 1124 AM Installation Mounting the PhoneOn a Desk Top Connecting and Charging the Battery Pack Setting the Dialing Mode Setting the HANDSET’S Ringer TONE/VOLUME Setting the Number of RingsTurning the BASE’S Ringer on and OFF Setting the DAY/TIME Setting Auto TalkTurning Caller ID/CALL Waiting on or OFF Telephone OperationStoring Your Area Code Answering Calls with the Speakerphone Adjusting the Handset VolumeSelecting the Channel Switching Between the Handset and Speakerphone Using Both the Handset and SpeakerphoneUsing Flash Using RedialUsing a Headset PagingMemory Dialing Storing a Name and Number in MemoryEntering a Pause Editing or Deleting a Number in MemoryReviewing Memory Numbers Dialing a Memory Number Caller ID OperationReviewing Caller ID Records Caller ID Messages ADDING/DELETING the Area CodeDialing Numbers from a Caller ID Record Storing a Caller ID Record to MemorySetting the Record Time Answering System OperationDeleting Caller ID Records Selecting the Outgoing MessageScreening Calls Setting the Answering System to Answer CallsRecording Incoming Messages Recording a Conversation Recording a MemoPlaying Messages Deleting Messages Adjusting the Answering SYSTEM’S VolumeRemote Operation Using Remote Commands Troubleshooting Problem SuggestionBe sure the battery pack is correctly connected Care and Maintenance Replacing the Battery Pack FCC Wants YOU to Know LightningLimited One-Year Warranty