AKG Acoustics CS 5 IU Interpreter Station, CS 5 IU control panel, inputs, and outputs

Page 30

Section 6: CS 5 IU Interpreter Station

6.1 Introduction

The CS 5 IU adds interpretation capabilities to the CS 5 conference system. It provides inputs and outputs for a goose- neck microphone and headphones or a headset, a built-in loudspeaker, source and target language selectors, a mi- crophone switch, cough button, "slow" signal button, and a signal button for requesting a technician's assistance.

6.2 Control Panel, Inputs, and Outputs

Fig. 8: CS 5 IU control panel, inputs, and outputs.

INPUT SELECT: These four keys select the source language signal that is routed to the headphone output.

1FLOOR: Selects the floor (main mix) signal.

2 A: Selects the next item from a list.

3 B: Selects the previous item from a list.

4 RELAY: Selects the relay-language channel specified by the organizer or chief interpreter.

5 Backlit LC display.

6BASS: Cuts/boosts the low-frequency range of the headphone or loudspeaker signal.

7TREBLE: Cuts/boosts the high-frequency range of the headphone or loudspeaker signal.

8 VOLUME: Sets the volume level of the headphone or loudspeaker signal.

9Microphone status LED: Indicates the current operating status of the microphone:

•Lit: microphone is open (MICROPHONE switch (14) set to "ON").

•Dark: microphone is off or muted (MICROPHONE switch (14) set to "OFF" or "MUTE").

CS 5 User Manual

- 30 -

Image 30

Contents Conference System Table of Contents Table of Contents Symbols Used Environment Safety and EnvironmentSafety Instructions FCC StatementGeneral Page System Examples Simple Discussion SystemExample 1 Simple discussion system Computer-controlled Discussion System Example 2 Larger discussion system with computer controlInfrared Interpretation System Layout Wiring Diagram Example 4 Large conference system layout and wiring diagram Page General Power Switches power to the Base Unit on I or OFFCS 5 BU Base Unit Front PanelCS 5 BU Base Unit Rear PanelSetting Up the Base Unit Block DiagramConfiguring the Dip Switches Base Unit dip switchesSelecting NOM Limitation/Interpretation Channels Powering Up Setting LevelsCS 5 BU Base Unit CS 5 DU Delegate Station IntroductionControls, Inputs, and Outputs Making Connections Setting UpCS 5 DU Delegate Station Selecting Operating ModesCS 5 DU Delegate Station CS5 VU Voting/Chairperson Station Control Panel, Inputs, and OutputsRefer to Mini jack for stereo headphones CS5 VU Voting/Chairperson StationFunction Switch positions Delegate Mode Press soft button 3 Back to return to the main menuPresident Mode President menu and selectable submenusControlling a Ballot or Opinion Poll President Mode Voting/PollingVoting in Delegate Mode … or like this…Press any button to return to the President main menu Chip Card Identification CS 5 IU Interpreter Station CS 5 IU control panel, inputs, and outputsCS 5 IU Interpreter Station OutputSelecting Station Addresses Selecting Target Language ChannelsSelect Next press Relay to bring up this screen List of Available Language Names Selecting the Microphone TypeSelect your target language Using the Interpreter StationMicrophone signal will be automatically routed to output a Controlling the microphonesCS 5 IU Interpreter Station CS 5 IRT 1 and CS 5 IRT 2 Infrared Radiators PlacementInfrared Transmission System GeneralMounting Connect each infrared radiator to powerInfrared Transmission System ConnectionsCS 5 IRR 7 Infrared Receiver Using the Infrared Receiver Replacing BatteriesCS 5 CU 50 Charger/Storage Case Charging BatteriesUnlock and remove the lid from the flight case Battery Care Remove the receiver from the charging slotSystem Components Specifications CS 5 BUSpecifications Connector PinoutsSystem Physical Dimensions Signal/noise ratio Width CS 5 DU/VUDepth Circuited input Headphone Output Power Physical Dimensions WidthCS 5 PS CS 5 IRT 1 and CS 5 IRT CS 5 IRRCS 5 CU Quick Charging Mode Charging currentTrickle Charging Mode Charging current Conformity10/09/9100 U