AKG Acoustics user manual CS 5 IU Interpreter Station

Page 35

Section 6: CS 5 IU Interpreter Station

- Method 2: the interpreter taking over presses the appropriate OUTPUT SELECT key. The red LED on the micro- phone comes on, the relieved colleague's microphone is automatically muted, and the red LED on that micro- phone goes dark.

Note that when using this method, one microphone will always be open. To make sure your listeners will not hear any of your internal conversations, always set the MICROPHONE switches on both control panels to OFF when none of you is interpreting.

5.Controlling talkers:

•If the person delivering a speech talks too fast, press <CALL> momentarily. This causes the green LED on the microphone arm on the talker's Delegate Unit to flash for five seconds. The display on your control panel shows the message "SENDING SLOWLY PLEASE". To stop the signal before the five seconds are over, press <CALL> again.

6.Calling a technician (if the system is computer controlled and a technician is available):

•If there is a technical problem or you have run out of water, etc. hold down <CALL> for at least three seconds. This causes an appropriate message to appear on the computer monitor and the message "CALLING TECHNI- CIAN" to appear on your control panel display. To delete the messages, press and hold <CALL> again for at least three seconds.

CS 5 User Manual

- 35 -

Image 35

Contents Conference System Table of Contents Table of Contents Symbols Used FCC Statement Safety and EnvironmentSafety Instructions EnvironmentGeneral Page Example 1 Simple discussion system System ExamplesSimple Discussion System Example 2 Larger discussion system with computer control Computer-controlled Discussion SystemInfrared Interpretation System Layout Wiring Diagram Example 4 Large conference system layout and wiring diagram Page Front Panel Power Switches power to the Base Unit on I or OFFCS 5 BU Base Unit GeneralRear Panel CS 5 BU Base UnitBlock Diagram Setting Up the Base UnitSelecting NOM Limitation/Interpretation Channels Configuring the Dip SwitchesBase Unit dip switches Setting Levels Powering UpCS 5 BU Base Unit Controls, Inputs, and Outputs CS 5 DU Delegate StationIntroduction Selecting Operating Modes Setting UpCS 5 DU Delegate Station Making ConnectionsCS 5 DU Delegate Station Control Panel, Inputs, and Outputs CS5 VU Voting/Chairperson StationCS5 VU Voting/Chairperson Station Refer to Mini jack for stereo headphonesFunction Switch positions Press soft button 3 Back to return to the main menu Delegate ModePresident menu and selectable submenus President ModeVoting/Polling Controlling a Ballot or Opinion Poll President ModePress any button to return to the President main menu Voting in Delegate Mode… or like this… Chip Card Identification CS 5 IU control panel, inputs, and outputs CS 5 IU Interpreter StationOutput CS 5 IU Interpreter StationSelect Next press Relay to bring up this screen Selecting Station AddressesSelecting Target Language Channels Selecting the Microphone Type List of Available Language NamesControlling the microphones Using the Interpreter StationMicrophone signal will be automatically routed to output a Select your target languageCS 5 IU Interpreter Station General PlacementInfrared Transmission System CS 5 IRT 1 and CS 5 IRT 2 Infrared RadiatorsConnections Connect each infrared radiator to powerInfrared Transmission System MountingCS 5 IRR 7 Infrared Receiver Replacing Batteries Using the Infrared ReceiverUnlock and remove the lid from the flight case CS 5 CU 50 Charger/Storage CaseCharging Batteries Remove the receiver from the charging slot Battery CareSystem Components CS 5 BU SpecificationsConnector Pinouts SpecificationsSystem Depth Physical Dimensions Signal/noise ratio WidthCS 5 DU/VU Physical Dimensions Width Circuited input Headphone Output PowerCS 5 PS CS 5 IRR CS 5 IRT 1 and CS 5 IRTConformity Quick Charging Mode Charging currentTrickle Charging Mode Charging current CS 5 CU10/09/9100 U