Multi-Tech Systems iCell GPRS (MTSMC-G2-IP manual Syntax AT#VALL

Page 18

Part 1 – AT Commands for All Universal IP Devices

Chapter 1 – General AT Commands for All Universal IP Devices

Syntax: AT#VALL

Possible Responses – Applies to All Except MT100SEM-IP

#ANSWERMODE: 0

#CALLBACKTIMER: 2

#CALLSCREENNUM: "0"

#DIALN1: ""

#DIALN2: ""

#DIALSELECT: 1

#GPRSMODE: 1

#PHYTIMEOUT: 15

#REDIALCOUNT: 0

#REDIALDELAY: 5

#RINGCOUNT: 0

#AUTOCONNECT: 0

#ISPUN: ""

#ISPPW: ""

#PPPMODE: 3

#PPPMYIP: 0.0.0.0

#PPPPEERIP: 0.0.0.0

#PPPSERVPW: ""

#PPPSERVUN: ""

#APNPW: ""

#APNSERV: ""

#APNUN: ""

#GPRSCID: 1

#DNSSERV1: "0.0.0.0"

#DNSSERV2: "0.0.0.0"

#FTPGETFILENAME: ""

#FTPGETPATH: ""

#FTPPORT: 21

#FTPPUTFILENAME: ""

#FTPPUTPATH: ""

#FTPPW: ""

#FTPSERV: ""

#FTPTYPE: I

#FTPUN: ""

#FTPMODE: 0

#POP3HEADERMODE: 1

#POP3PORT: 110

#POP3PW: ""

#POP3SERV: ""

#POP3UN: ""

#DOMAIN: ""

#SENDERADDR: ""

#SENDERNAME: ""

#SMTPPORT: 25

#SMTPPW: ""

#SMTPSERV: ""

#SMTPUN: ""

#BODY1: ""

#CCREC1: ""

#REC1: ""

#SUBJ1: ""

#BODY2: ""

#CCREC2: ""

#REC2: ""

#SUBJ2: ""

#BODY3: ""

#CCREC3: ""

#REC3: ""

#SUBJ3: ""

#DLEMODE: 1,1

#TCPPORT: 1,0

#TCPSERV: 1,""

#TCPTXDELAY: 1,100

#UDPPORT: 0

#UDPSERV: ""

#UDPTXDELAY: 100

#PINGDELAY: 1

#PINGNUM: 4

#PINGREMOTE: ""

#AUTHENT: NONE

+IPR: 115200

+ICF: 2,4

+IFC: 2,2

V:1

E:1

&S: 1

&C: 1

&D: 0

#KEEPALIVEMODE: 0

#KEEPALIVEPORT: 0

#KEEPALIVEDELAY: 100

#KEEPALIVESERV: ""

#LEGACYMODE: 0

#AUTORESET: 0

#ATCMD: 1,""

#ATCMD: 2,""

#ATCMD: 3,""

#ATCMD: 4,""

#PERSISTENTSOCKET: 0

#OUTPORT: 37500

#GPIO: 1,1,0,0,0,0

#GPIO: 2,1,0,0,0,0

#GPIO: 3,0,0,0,0,0

#GPIO: 4,0,0,0,0,0

#GPIO: 5,3,0,0,0,0

OK

Universal IP AT Commands Reference Guide (Document S000457K)

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Universal IP Product Number of This Document S000457K, Version K CopyrightContents Display Command Ping AT Commands for All Universal IP Devices Set Commands #VTELNET View Telnet Settings Incoming Call Management Commands 105 103104 106Part AT Commands for All Universal IP Devices Turn Echo ON/OFF Set CommandsAT Command Mode IdentificationRlsd DCD Option Turn On or Off Default ConfigurationReset Factory Defaults DTR OptionStore Factory Defaults to NVM +ICF DTE-DCE Character Framing#DELFLASH Erase Flash Memory Parameter Values +IFC Set Flow Control+IPR Set Serial Speed Display#LEGACYMODE Legacy Mode Enable/Disable #RESET Reset Main Processor or Internal Modem#SHIELDCHAR Configure the Shielding Character for Dlemode AT#ESCAPECHAR=parameter1 Display Commands#ESCAPECHAR Configure the Escape Character for Dlemode AT#VSHOWSERIALAT#VSHOWUPTIME #VVERSION Display Software Version#VSTATE Display Current State of Physical Connection AT#VSHOWUPTIMES#VALL Display All Parameters Syntax AT#VALL Possible Responses MT100SEM-IPSyntax AT#VALL Possible Responses Applies to All Except MT100SEM-IP#SENDERADDR Set Sender Address Smtp AT Commands for All Universal IP Devices#SENDERNAME Set Sender Name #CCRECi Set Additional Recipient CC#SUBJi Set Email Pre-Defined Subject Text #DOMAIN Set Domain Name of the Sender#RECiADD Set Email Address Syntax AT#DOMAIN=value#SMTPPORT Set Smtp Server Port Syntax AT#SMTPNETWORKTIMER=parameter1#BODYi Set Pre-Defined Email Combinations Syntax AT#SMTPPORT=value#SMTPPW Set Smtp Password #SMTPSERV Set Smtp Server Address#SMTPUN Set Smtp User Name #SENDMAILi Send Mail without Interactive Mode AT#SENDMAILi#SENDMAIL3 #PUTMAIL Send Mail to Recipient with Interactive Mode Command Possible ResponsesSyntax AT#PUTMAIL #VMAILi Display Email Parameters for Respective Mail ID #SMTPAUTH Authentication on or OFF#VSMTP Display Smtp Parameters OFF#POP3HEADERMODE POP3 Header POP3 AT Commands for All Universal IP Devices#POP3PW Set POP3 Password #POP3PORT Set POP3 Server Port#GETMAIL Retrieve Host Mail Display Command#POP3UN Set POP3 User Name #VPOP3 POP3 Module Parameters#FTPPORT Enter FTP Server Port FTP AT Commands for All Universal IP Devices#FTPMODE Enter FTP Mode #FTPTYPE Specify Data Type#FTPUN Set FTP User Name #FTPPW Set FTP Password#FTPSERV Specify FTP Server Address #FTPGETFILENAME Set FTP Download File NameAT#FTPGET #FTPGET Download Files from FTP Server#FTPPUT Upload Files to FTP Server AT#FTPPUT#FTPGETPATH Set Path to Get a File from FTP Server #FTPPUTPATH Set Path to Send Files to FTP Server#FTPAPPEND Append Data to Server #VFTP Display FTP Parameters Syntax AT#VFTP Values FtpservDefaults 0,1 TCP AT Commands for All Universal IP Devices#DLEMODE Set DLE Mode #PERSISTENTSOCKET Persistent Socket#TCPSERV Set Address of Remote TCP Server #TCPTXDELAY Time Delay#TCPPORT Set TCP Port for Remote Peer AT#TCPPORT=id,TCP Port number for remote peer valueAT#TCPPACKETMIN=parameter1, parameter2 #TCPPACKETMIN TCP Client Transmit Packet Minimum Size#TCPPACKETMAX TCP Client Transmit Packet Maximum Size Parameter#TCPINACTIVITYTIMER TCP Client Inactivity Timeout Value AT#TCPINACTIVITYTIMER=parameter1, parameter2AT#TCPNETWORKTIMER=parameter1, parameter2 AT#TCPTELNETMODE=parameter1, parameter2 #TCPTELNETMODE Enable/Disable TCP Client Telnet ProtocolLine feed character not just any key AT#TCPTELNETPW=parameter1, parameter2AT#TCPTELNETUN=parameter1, parameter2 #LTCPSTART Open Listening Mode#TCPTELNETUN Set the TCP Client Telnet Protocol User Name Syntax AT#LTCPSTART=id#OTCP Open a TCP Connection #LTCPSTOP Close TCP Listening Mode#OUTPORT UDP/TCP Local Port Number Dlemode Value Notes#VTCP Display TCP Parameters Example Command Possible ResponsesTcptxdelay 2 AT#VTCP=id or AT#VTCP#UDPPACKETMIN UDP Client Transmit Packet Minimum Size UDP AT Commands for All Universal IP DevicesDefaults Example Result CodesCommand Examples #UDPINACTIVITYTIMER UDP Client Inactivity Timeout ValueAT#UDPINACTIVITYTIMER=parameter1 #UDPPACKETMAX UDP Client Transmit Packet Maximum Size#UDPREMOTEPORT Remote Port Number Default Responses#UDPIGNORESRCPORT Ignore Send Source Port #UDPPORT UDP Port NumberDefault Value #UDPTXDELAY Delay before Sending UDP DatagramSyntax AT#UDPTXDELAY=Value #UDPSERV UDP Server AddressUdpsesrv Udptxdelay #UDPDLEMODE Set DLE Mode#LUDPSTART Initiate the UDP Session in Listen Mode AT#UDPDLEMODE=parameter1#VUDP Display UDP Module Configuration #LUDPSTOP Close UDP Listening Mode#OUDP Initiate UDP Session in Active Mode Syntax AT#VUDP#PINGNUM Number of Ping Requests Ping AT Commands for All Universal IP Devices#PINGDELAY Ping Delay Time #PINGREMOTE IP Address of Ping RequestSyntax AT#VPING Pingnum Pingremote Pingenable Pingdelay#VPING Display Ping Parameters Values DisplayedPart AT Commands for SocketEthernet IP #IPADDR Set Static IP Address General AT Commands for SocketEthernet IP#DHCP Dhcp On or Off #IPGATEWAY Set Gateway Address#DNSSERV2 Set Secondary DNS Server #IPNETMASK Set Subnet Mask#DNSSERV1 Set DNS Server IP Address #EMACSPD Set Ethernet Connection#VDNS Display Configuration of DNS Servers #HOSTNAME Configure the Dhcp Client Host Name#ETHIFSTATUS View Network Interface Settings Values None Display Example Interface UP#VIP View Address Settings Syntax AT#VIP Values None#AUTODISC Auto Discovery On/Off Auto Discovery AT Commands for the SocketEthernet IP#AUTODISCTIMER Auto Discovery Timer #AUTODISCPORT Auto Discovery Port#AUTODISCPASSWORD Sets Auto Discover Password #VAUTODISC Display Auto Discovery Commands#AUTODISCUSERNAME Set Auto Discover User Name Part AT Commands for SocketWireless Wi-Fi Devices IP AT Commands for SocketWireless Wi-Fi Enable DNS #IPDNSSERV Configure the DNS ServerDisables DNS AT#IPDNSSERV#IPQUERY Give a Domain Name #IPRELEASE Release a Dhcp Address Assigned by the Server#IPRENEW Renew the Dhcp Information from the Server #IPRESOLV Is There a Connection with DNS or NotResponse Values #IPDNSTABLE Display DNS TableAT#IPDNSTABLE Syntax AT#VDNSManual Answer of TCP or UDP Connection General AT Commands for SocketWireless Wi-FiPrevious Command S2 Escape Sequence#WATCHDOGTIMER Watchdog Timer #BOOTMSG Enable/Disable Boot Message#WATCHDOG Enable/Disable Watchdog AT#BOOTMSG=0,1#TELNETPORT- Set Telnet Port Values Default#TELNET Start/Stop Telnet Session #TELNETUSER Set Telnet UserAT# Telnetpassword = 64 char string #TELNETPASSWORD Set Telnet Password#VTELNET View Telnet Settings AT#TELNETPASSWORD?#WLANNETWORKMODE Wlan Network Mode Wlan AT Commands for SocketWireless Wi-Fi#WLANSECURITYMODE Security Mode of Wlan Module #WLANCOUNTRYCODE Country Code#WLANSSID Ssid of Wlan #WLANSCANMODE Scanning Mode#WLANIBSSCHANNEL Channel for Ad-Hoc Mode #WLANDATARATE Wlan Transmission Data Rate#WLANCONNECT Connect with AP #WLANENABLE Auto Connect Module with AP#WLANDOZE= Moves Module into or out of Power Save #WLANDISCONNECT Disconnect with APKeyindex = #WLANSCAN Scan Wireless Networks#WLANPROFILEn=n Change the Wlan Profile Syntax AT#WLANSCAN#WLANROAM Enable/Disable Roaming #WLANGETRSSI Received Signal Strength#WLANACTIVATE Move Module out of Power Save #WEP64KEY Keys for WEP64 Security Mode#WPA2PSKKEY Keys for WPA2 PSK Security Mode #WEP128KEY Keys for WEP128 Security Mode#WPAPSKKEY Keys for WPA PSK Security Mode #WEPKEYID Set the Default TX Key IndexAT#WEP? #WEP? See the Value of the WEP Keys#WLANPROFILE Display the Wlan Profile AT#WLANSETPROFILEvalue?AT#WLAN? #WLAN? Wlan Module#WLANASSOCINFO Display Association Information AT#WLANASSOCINFOAT Commands for the Following Devices AT Commands for +WOPEN Set IP Mode or Modem Mode#AUTHENT Authentication Type AT#ANSWERMODE=value #ANSWERMODE Set Answering Mode#SMSPHRASE Set Incoming SMS Phrase AT#SMSPHRASE=parameter1#KEEPALIVEMODE Keep-Alive Mode #CALLBACKTIMER Set Automatic Call-Back Wait#CALLSCREENNUM Set Caller ID Service Default Example#KEEPALIVEDELAY Keep-Alive Delay #KEEPALIVEPORT Keep-Alive Port Number#KEEPALIVESERV Keep-Alive Server Address #PHYTIMEOUT Set Inactivity Time #ATCMD Customize Dial-Up Commands#REDIALDELAY Set Call Retry Delay #REDIALCOUNT Set Connection Attempts Allowed#RINGCOUNT Set Number of Rings/Automatic Operation #DIALN1 Set Primary Dial-Up Number#DIALN2 Set Secondary Dial-Up Number #ISPPW Set ISP Password #DIALSELECT Set Internet Connection Number#ISPUN Set ISP User Name #CONNECTIONSTOP Stop Communication Incoming Call Management Commands#ACCEPT Answer Incoming Call AT#ACCEPT#CONNECTIONSTART Start Communication AT#CONNECTIONSTART#PPPMODE Set TCP/IP Behavior #PPPMYIP Set IP Address When Using PPP#AUTOCONNECT Automatically Connect the PPP Link #PPPPEERIP Set IP Address for Remote PPP#APNSERV Set Access Point Name #PPPSERVPW Set Remote PPP Client Password#APNPW Set Access Point Name Password #APNUN Set Access Point User Name#GPRSMODE Activate Switching Between GSM and Gprs #GPRSCID Set PDP Context Identifier#DISPLAYIP Display IP Addresses AT#VPPP #VPPP Display PPP Parameters#VPHY Display Physical Parameters AT#VPHYPart Gpio AT Commands Gpio AT CommandsValues Gpio Function Gpio AT CommandsAbout Gpio Trigger Level\r\n#GPIOR VALUE1,VALUE2\r\n AT#GPIOR=parameterGpio Port Send AT#GPIOR=1\r#GPIOTRIGGER Configure the Gpio pin and trigger type Description Configure the Gpio pin and trigger typeSyntax AT#GPIOTRIGGER=parameter1,parameter2 Part AT Commands for GPS-Enabled Device Commands for GPS-Enabled Device#GPSPORT Set GPS Host Port AT Commands for GPS Enable Products#GPSSERV Set GPS Host Server Address #GPSPROTO Set GPS Host Protocol#GPSURAIS Set GPS Unique Remote Asset Identification String #GPSPW Set GPS Host Login Password#GPSGPGGA Enable/Disable Gpgga Message #GPSINTERVAL Set GPS Server Transmission Interval#GPSGPGSV Enable/Disable Gpgsv Message #GPSGPGLL Enable/Disable Gpgll Message#GPSGPGSA Enable/Disable Gpgsa Message #GPSGPRMC Enable/Disable Gprmc Message#GPSGPVTG Enable/Disable Gpvtg Message #GPSINTERVALLOC GPS Local Transmission Interval#GPSGETMESSAGE Get Queued GPS Message Gpsprefixgpsuraisnmeamessagecrlf GPS Message SyntaxGPS Message Examples WhereGPS Configuration Examples Application Note GPS Nmea Messages Introduction Nmea Protocol OverviewGGA Global Positioning System Fix Data StructureExample GLL Latitude/Longitude GSA Gnss DOP and Active SatellitesGSV Gnss Satellites in View $GPGSVSNR $GPRMC RMC Recommended Minimum Specific Gnss DataVTG Course Over Ground and Ground Speed $GPVTGPart Appendixes Standard AT Messages Numeric Verbose Description Appendix a Response Messages Error CodesResponse Messages RingError Codes Error CodesNumeric Description Response Messages Examples Sending an Email AT#PUTMAIL Commands ResponsesAppendix B Response Message Examples Sending/Retrieving Email Response MessagesRetrieving an Email AT#GETMAIL Commands Responses AT#POP3PORT=110 AT#GETMAILAT#FTPPUTPATH= Upload a file to an FTP Server AT#FTPPUT Commands ResponsesFTP Download / Upload Files Response Messages AT#FTPPUTAct as a TCP Server AT#LTCPSTART Commands Responses Act as a TCP Client AT#OTCP Commands ResponsesTCP Socket Response Messages Index #FTPAPPEND Append Data to Server#UDPTXDELAY Delay before Sending UDP Datagram Close TCP Listening Mode #LTCPSTOP #LTCPSTART Open Listening Mode #PINGNUM Number of Ping Requests Commands for SocketModem IP Commands for SocketWireless Wi-Fi #PERSISTENTSOCKET Delay before Sending UDP Initiate the UDP Session in Listen Mode 119

iCell GPRS (MTSMC-G2-IP specifications

Multi-Tech Systems iCell GPRS (MTSMC-G2-IP) is a versatile and powerful device designed for seamless connectivity in various applications, particularly in industrial and commercial environments. Known for its robust performance, the iCell GPRS module incorporates advanced technologies that enable effective communication over GPRS networks, making it an ideal solution for IoT applications, remote monitoring, and data collection processes.

One of the main features of the iCell GPRS is its dual SIM capability, which enhances network reliability and ensures continuous connectivity even in the event of network outages. By allowing the use of two SIM cards from different carriers, the device can switch between networks automatically, thereby minimizing downtime and maintaining critical communication channels.

The iCell GPRS supports various protocols including TCP/IP, UDP, and MQTT, which facilitates seamless integration with a range of applications. This flexibility in communication protocols allows developers to create customized solutions tailored to their specific needs, ensuring that the device can fit seamlessly into their existing infrastructure.

Another key characteristic of the MTSMC-G2-IP is its compact design and durability, making it suitable for deployment in a variety of environments. It features a wide operating temperature range that allows it to function efficiently in both extreme heat and cold, thereby catering to diverse applications across different industries. Additionally, the device is designed for easy installation and integration, which helps reduce deployment time and costs.

The iCell GPRS also includes built-in security features such as firewalls and secure data transmission protocols, protecting sensitive information from unauthorized access. This is particularly important for applications in sectors such as healthcare, finance, and transportation, where data integrity and security are paramount.

Furthermore, the device is equipped with various I/O ports that facilitate connectivity with external sensors, actuators, and other hardware. This feature makes it highly adaptable for monitoring and control systems, enabling users to gather real-time data and respond promptly to changing conditions.

In sum, the Multi-Tech Systems iCell GPRS (MTSMC-G2-IP) is a reliable and feature-rich solution designed for modern communication needs. Its dual SIM support, protocol versatility, robust design, and integrated security features make it an ideal choice for IoT and remote monitoring applications across numerous industries. Whether used in industrial automation, environmental monitoring, or smart cities, the iCell GPRS stands out as a dependable device that enhances connectivity and operational efficiency.
Top Page Image Contents