TP-Link manual TL-WA730RE 150Mbps Wireless Range Extender User Guide, 23 Diagnostic

Page 50

Figure 4-23 Diagnostic

TL-WA730RE150Mbps Wireless Range Extender User Guide

Figure 4-23 Diagnostic

¾Diagnostic Tools - Click the radio button to select one diagnostic tool.

•Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway by using the Internet Control Message Protocol (ICMP) protocol's mandatory Echo Request datagram to elicit an ICMP Echo Response from a host or gateway. You can use ping to test both numeric IP address or domain name. If pinging the IP address is successful, but pinging the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries.

•Traceroute - This diagnostic tool determines the path taken to a given host by sending Internet Control Message Protocol (ICMP) Echo Request messages with varying Time to Live (TTL) values to the destination. Each gateway along the path is required to decrement the TTL in an IP packet by at least 1 before forwarding it. Effectively, the TTL is a maximum link counter. When the TTL on a packet reaches 0, the gateway is expected to return an ICMP Time Exceeded response to your device. Traceroute determines the path by sending the first Echo Request message with a TTL of 1 and incrementing the TTL by 1 on each subsequent transmission until the target responds or the maximum number of hops is reached. The maximum number of hops is 20 by default and can be specified in the field "Traceroute Max TTL". The path is determined by examining the ICMP Time Exceeded messages returned by intermediate gateways and the Echo Reply message returned by the destination. However, some gateways do not

43

Image 50

Contents TL-WA730RE 150Mbps Wireless Range Extender Rev 1.0.0COPYRIGHT & TRADEMARKS All rights reservedFCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Restriction National restrictionsCountry Reason/remarkETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 150Mbps Wireless Range Extender ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN60950-12006Hardware Installation CONTENTSPackage Contents Chapter 3 Quick Installation GuideAppendix D Specifications Appendix B Factory DefaultsAppendix C Troubleshooting Appendix A Application ExamplePackage Contents ConventionsChapter 2 Hardware Installation Overview of This GuidePackage Contents Chapter3 Quick Installation Guidethat the AP will automatically assign an IP address for Introduces how to set your AP to be a DHCP server so4.6 DHCP your PCChapter 1 Introduction 1.2 Main FeaturesFeatures 1.1 Product OverviewTL-WA730RE 150Mbps Wireless Range Extender User Guide 1.3 Appearance1.3.1 The Front Panel LED Explanation1.3.2 The Rear Panel Ensure the Range Extender is powered on before it restarts completely2.1 Before You Begin Chapter 2 Hardware Installation2.3 Connecting the Device 2.2 Basic Requirements1. Connect the Cable or DSL modem to a Router Chapter 3 Quick Installation Guide 3.1 Configure the PC150Mbps Wireless Range Extender User Guide 1 Select Use the following IP address 3.2 Quick Setup Figure 3-9 Quick Setup Figure 3-12 Quick Setup - Range Extender Mode Figure 3-11 AP ListB. When you choose Access Point, take the following steps TL-WA730RE 150Mbps Wireless Range Extender User Guide Chapter 4 Configure the Device 4.1 Status4.2 Quick Setup 4.3 QSSTo add a new device Method OneFigure 4-3 Add A New Device Next TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.4 Network 4.5 Wireless 4.5.1 Wireless SettingsTL-WA730RE 150Mbps Wireless Range Extender User Guide TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.2 Wireless Security 1 Range Extender ¾ WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key 2 Access Point TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.3 Wireless MAC Filtering To set up an entry, follow these instructions To modify or delete an existing entry4.5.4 Wireless Advanced 4.5.5 Throughput Monitor 4.5.6 Wireless Statistics 4.6 DHCP This page will be refreshed automatically every 5 seconds4.6.1 DHCP Settings 4.6.2 DHCP Clients List 4.6.3 Address ReservationTo Reserve IP addresses 4.7 System ToolsThe changes wont take effect until the device reboots To modify A Reserved IP address4.7.1 SNMP 4.7.2 Diagnostic Figure 4-23 Diagnostic 4.7.3 Ping Watch Dog 1 Only one user can use this tool at one time4.7.4 Firmware Upgrade To upgrade the devices firmware, follow these instructions 4.7.5 Factory Defaults4.7.6 Backup & Restore 2. Wrong process will lead the device unmanaged 4.7.7 RebootTo restore the devices configuration, follow these instructions 4.7.8 Password 4.7.9 System LogFigure 4-31 System Log Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless Range Extender User Guide Common Default Settings Appendix B Factory DefaultsDefault Value Wireless2. The LAN LED is not lit Appendix C Troubleshooting1. No LEDs are lit on the access point Physical and Environment Appendix D SpecificationsGeneral Appendix E Glossary TL-WA730RE 150Mbps Wireless Range Extender User Guide

Related manuals

Manual 68 pages 59.99 Kb