TP-Link manual DHCP Settings, TL-WA730RE 150Mbps Wireless Range Extender User Guide

Page 45

4.6.1 DHCP Settings

TL-WA730RE150Mbps Wireless Range Extender User Guide

4.6.1 DHCP Settings

Selecting DHCP > DHCP Settings will enable you to set up the AP as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page (shown as Figure 4-18):

Figure 4-18 DHCP Settings

¾DHCP Server - Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your AP. The default setting is Disable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer.

¾Start IP Address - This field specifies the first address in the IP Address pool. 192.168.1.100 is the default start IP address.

¾End IP Address - This field specifies the last address in the IP Address pool. 192.168.1.199 is the default end IP address.

¾Address Lease Time - Enter the amount of time for the PC to connect to the AP with its current assigned dynamic IP address. The time is measured in minutes. After the time is up, the PC will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.

¾Default Gateway (optional) - Enter the IP address of the gateway for your LAN. The factory default setting is 0.0.0.0.

¾Default Domain (optional) - Enter the domain name of the your DHCP server. You can leave the field blank.

¾Primary DNS (optional) - Enter the DNS IP address provided by your ISP. Consult your ISP if you don’t know the DNS value. The factory default setting is 0.0.0.0.

¾Secondary DNS (optional) - Enter the IP address of another DNS server if your ISP provides two DNS servers. The factory default setting is 0.0.0.0.

Click Save to save the changes.

38

Image 45

Contents Rev 1.0.0 TL-WA730RE 150Mbps Wireless Range ExtenderAll rights reserved COPYRIGHT & TRADEMARKSFCC STATEMENT CE Mark WarningFCC RF Radiation Exposure Statement Country National restrictionsRestriction Reason/remarkProduct Description 150Mbps Wireless Range Extender DECLARATION OF CONFORMITYETSI EN 300 328 V1.7.1 ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN60950-12006Package Contents CONTENTSHardware Installation Chapter 3 Quick Installation GuideAppendix C Troubleshooting Appendix B Factory DefaultsAppendix D Specifications Appendix A Application ExampleConventions Package ContentsPackage Contents Overview of This GuideChapter 2 Hardware Installation Chapter3 Quick Installation Guide4.6 DHCP Introduces how to set your AP to be a DHCP server sothat the AP will automatically assign an IP address for your PCFeatures 1.2 Main FeaturesChapter 1 Introduction 1.1 Product Overview1.3.1 The Front Panel 1.3 AppearanceTL-WA730RE 150Mbps Wireless Range Extender User Guide LED ExplanationEnsure the Range Extender is powered on before it restarts completely 1.3.2 The Rear Panel2.3 Connecting the Device Chapter 2 Hardware Installation2.1 Before You Begin 2.2 Basic Requirements1. Connect the Cable or DSL modem to a Router 3.1 Configure the PC Chapter 3 Quick Installation GuideTL-WA730RE 1 Select Use the following IP address 3.2 Quick Setup Figure 3-9 Quick Setup Figure 3-11 AP List Figure 3-12 Quick Setup - Range Extender ModeB. When you choose Access Point, take the following steps TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.1 Status Chapter 4 Configure the Device4.3 QSS 4.2 Quick SetupMethod One To add a new deviceFigure 4-3 Add A New Device Next TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.4 Network 4.5.1 Wireless Settings 4.5 WirelessTL-WA730RE 150Mbps Wireless Range Extender User Guide TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.2 Wireless Security 1 Range Extender ¾ WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key 2 Access Point TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.3 Wireless MAC Filtering To modify or delete an existing entry To set up an entry, follow these instructions4.5.4 Wireless Advanced 4.5.5 Throughput Monitor 4.5.6 Wireless Statistics This page will be refreshed automatically every 5 seconds 4.6 DHCP4.6.1 DHCP Settings 4.6.3 Address Reservation 4.6.2 DHCP Clients ListThe changes wont take effect until the device reboots 4.7 System ToolsTo Reserve IP addresses To modify A Reserved IP address4.7.1 SNMP 4.7.2 Diagnostic Figure 4-23 Diagnostic 1 Only one user can use this tool at one time 4.7.3 Ping Watch Dog4.7.4 Firmware Upgrade 4.7.5 Factory Defaults 4.7.6 Backup & RestoreTo upgrade the devices firmware, follow these instructions 4.7.7 Reboot To restore the devices configuration, follow these instructions2. Wrong process will lead the device unmanaged 4.7.9 System Log 4.7.8 PasswordFigure 4-31 System Log Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless Range Extender User Guide Default Value Appendix B Factory DefaultsCommon Default Settings WirelessAppendix C Troubleshooting 1. No LEDs are lit on the access point2. The LAN LED is not lit Appendix D Specifications GeneralPhysical and Environment Appendix E Glossary TL-WA730RE 150Mbps Wireless Range Extender User Guide

Related manuals

Manual 68 pages 59.99 Kb