TP-Link manual TL-WA730RE 150Mbps Wireless Range Extender User Guide

Page 23

Manual background

TL-WA730RE150Mbps Wireless Range Extender User Guide

wireless network security, the default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.

¾Region - Specifies the region where the wireless function of the AP can be used. Select your region from the drop-down list. If your country or region is not listed, please contact your local government agency for assistance.

) Note:

Restricted by local law regulations, version for North America does not have region selection option.

¾Channel - This field determines which operating frequency will be used. The default channel is set to Auto, so the AP will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

¾Mode - This field determines the wireless mode which the AP works on.

These settings are only for basic wireless parameters, for advanced settings, please refer to Section 4.5: "Wireless."

4.Click the Next button. You will then see the Finish page.

Because there are something changed on the Wireless page, you will see the Finish page as shown in Figure 3-14.Click the Reboot button to make your wireless configuration to take effect and finish the Quick Setup.

Figure 3-14 Quick Setup – Finish

If you don’t make any changes on the Wireless page, you will see the Finish page as shown in Figure 3-15.Click the Finish button to finish the Quick Setup.

Figure 3-15 Quick Setup - Finish

16

Image 23

Contents Rev 1.0.0 TL-WA730RE 150Mbps Wireless Range ExtenderAll rights reserved COPYRIGHT & TRADEMARKSFCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning Reason/remark National restrictionsCountry RestrictionETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN60950-12006 DECLARATION OF CONFORMITYProduct Description 150Mbps Wireless Range Extender ETSI EN 300 328 V1.7.1Chapter 3 Quick Installation Guide CONTENTSPackage Contents Hardware InstallationAppendix A Application Example Appendix B Factory DefaultsAppendix C Troubleshooting Appendix D SpecificationsConventions Package ContentsChapter3 Quick Installation Guide Overview of This GuidePackage Contents Chapter 2 Hardware Installationyour PC Introduces how to set your AP to be a DHCP server so4.6 DHCP that the AP will automatically assign an IP address for1.1 Product Overview 1.2 Main FeaturesFeatures Chapter 1 IntroductionLED Explanation 1.3 Appearance1.3.1 The Front Panel TL-WA730RE 150Mbps Wireless Range Extender User GuideEnsure the Range Extender is powered on before it restarts completely 1.3.2 The Rear Panel2.2 Basic Requirements Chapter 2 Hardware Installation2.3 Connecting the Device 2.1 Before You Begin1. Connect the Cable or DSL modem to a Router 3.1 Configure the PC Chapter 3 Quick Installation GuideTL-WA730RE 1 Select Use the following IP address 3.2 Quick Setup Figure 3-9 Quick Setup Figure 3-11 AP List Figure 3-12 Quick Setup - Range Extender ModeB. When you choose Access Point, take the following steps TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.1 Status Chapter 4 Configure the Device4.3 QSS 4.2 Quick SetupMethod One To add a new deviceFigure 4-3 Add A New Device Next TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.4 Network 4.5.1 Wireless Settings 4.5 WirelessTL-WA730RE 150Mbps Wireless Range Extender User Guide TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.2 Wireless Security 1 Range Extender ¾ WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared key 2 Access Point TL-WA730RE 150Mbps Wireless Range Extender User Guide 4.5.3 Wireless MAC Filtering To modify or delete an existing entry To set up an entry, follow these instructions4.5.4 Wireless Advanced 4.5.5 Throughput Monitor 4.5.6 Wireless Statistics This page will be refreshed automatically every 5 seconds 4.6 DHCP4.6.1 DHCP Settings 4.6.3 Address Reservation 4.6.2 DHCP Clients ListTo modify A Reserved IP address 4.7 System ToolsThe changes wont take effect until the device reboots To Reserve IP addresses4.7.1 SNMP 4.7.2 Diagnostic Figure 4-23 Diagnostic 1 Only one user can use this tool at one time 4.7.3 Ping Watch Dog4.7.4 Firmware Upgrade To upgrade the devices firmware, follow these instructions 4.7.5 Factory Defaults4.7.6 Backup & Restore 2. Wrong process will lead the device unmanaged 4.7.7 RebootTo restore the devices configuration, follow these instructions 4.7.9 System Log 4.7.8 PasswordFigure 4-31 System Log Appendix A Application Example 3 Right-click the wireless connection icon “” on the screen of the PC and then select View Available Wireless Networks TL-WA730RE 150Mbps Wireless Range Extender User Guide Wireless Appendix B Factory DefaultsDefault Value Common Default Settings2. The LAN LED is not lit Appendix C Troubleshooting1. No LEDs are lit on the access point Physical and Environment Appendix D SpecificationsGeneral Appendix E Glossary TL-WA730RE 150Mbps Wireless Range Extender User Guide

Related manuals

Manual 68 pages 59.99 Kb