Ameriphone RC-200 Auto Dialing the first number stored in M1, Dialing by using the Scan button

Page 9

CHAPTER 5 (CONTINUED)

Auto Dialing the first number stored in M1.

A. From keypad

1. Press ON/OFF button or just press M1.

2. The number is dialed automatically

within 7 seconds.

4.The DIALOGUE RC automatically dials the number selected.

5.Press the ON/OFF button to hang up.

M U T EF L A S H / P A U S E

ON/OFF

H E A D S E TR E D I A L

M I C

Figure 16

B. Using Remote Transmitter With Scan

function on:

1.

Press Remote Transmitter.

2.

The number is dialed automatically

 

after scanning all memories 3 times.

C. With Scan function off:

1.

Press Remote Transmitter.

2.

The number is dialed automatically.

Dialing by using the SCAN button

Before you can use memory scanning for dial- ing, you must have the phone numbers stored in the memory first (page 6). To use memory scan- ning, the Scan function must be on. See Chapter 4 section C. Memory locations with no number stored are skipped. The memory direc- tory is scanned three times or until a number is selected. If no number is selected, the first number in M1 is dialed.

V O L

 

M U T E

P R O G

SCAN

H E A D S E T

1. Press the SCAN

 

M I C

button.

 

 

 

Figure 15

2.The memory location indicators light up as it scrolls down the memory locations.

If you have DIALOGUE RC–100: Only the first six memory locations are scanned.

If you have DIALOGUE RC–200: All 20 memory locations are scanned (It "beeps" when advancing to the next memory location.)

3.When the desired memory location is lit, press the SCAN button again to select.

Dialing using the Remote Transmitter

A. With Scan function on:

1.Press the Remote Transmitter to begin

scanning.

Figure 17

2.When the desired memory location is lit, press the Remote Transmitter. The DIALOGUE RC automatically dials the number selected.

3.Press the Remote Transmitter once to hang up.

B.With Scan function off:

1.Press the Remote Transmitter once.

2.It dials the first number stored in M1.

C.Answering phone calls

Using the keypad

 

 

1. When the phone rings,

M U T E

F L A S H / P A U S E

press the ON/OFF

H E A D S E T

ON/OFF

R E D I A L

M I C

 

button to turn it on.

 

 

2. When finished, press

 

Figure 18

the ON/OFF button to

 

 

hang up.

 

 

Using the Remote Transmitter

1. When the phone rings, press the Remote Transmitter to turn on.

2. Press the remote

 

Figure 19

button once to hang up.

 

7

Image 9
Contents Rcdialogue RC Important Safety Instructions Table of Contents Package Checklist Chapter Introduction714 714 897-4703 Fax Microphone Scan button Volume control Memory Program button Chapter Features IdentificationTone/pulse selector underneath Mute button Flash/Pause button On/Off button Redial buttonBattery included with RC-200 Speakerphone Chapter InstallationSetting up your RC Remote TransmitterTo turn the Remote Flash feature on or off RC-200 only Setting the Scan FunctionChapter To turn Voice Activation on or off RC-200 onlyMaking phone calls Dialing on the keypad Chapter OperationProgramming numbers into memory To program a number into memoryDialing using the Remote Transmitter Dialing by using the Scan buttonAnswering phone calls Using the keypad Using the Remote TransmitterVoice Activated answering Dialogue RC-200 only Other Operations Redialing the last number dialedDialogue RC turns on Flash button AIR Switch Chapter Optional AccessoriesPillow Switch Lapel MicrophoneQuick Start Guide Summary Press Remote Transmitter to hang up Symptom Cause and Remedy Sensitivity AdjustmentChapter Case of Difficulty Dialogue RC Channel SettingsChapter Maintenance FCC Information Chapter Warranty Or accessory switch Back-up battery Provided Chapter Feature SummaryContact US Index