VTech important safety instructions Basic Operation Using Your VT 9152 Cordless Telephone

Page 10

BASIC OPERATION

USING YOUR VT 9152 CORDLESS TELEPHONE

MAKING CALLS

Pick up the Handset and press PHONE/FLASH. When you hear a dial tone, dial the number. The IN USE/LOW BATT LED will illuminate when the Handset is in use.

If you make a mistake when dialing, press OFF to hang up, then press PHONE/FLASH to get a dial tone again.

ANSWERING CALLS

When the Handset rings, the IN USE/LOW BATT LED will flash on the Handset and the IN USE/CHARGING LED will flash on the Base Unit. Press any key on the Handset except OFF. If the Handset is in the Base Unit, simply pick it up to answer the call.

HANDSET VOLUME CONTROL

Use the Volume UP and DOWN keys, located on the bottom of the Handset keypad to adjust the earpiece volume to a comfortable level.

ENDING A CALL

Say “Bye-Bye”, then either press OFF on the Handset, or place the Handset in the Base Unit

cradle.

REDIAL

Press the REDIAL/PAUSE key to dial the last number you called. The Handset must be In Use for this feature to function.

CHANGING CHANNELS

If you notice noise or interference when using your Handset, press CHAN to switch to a clear channel. The feature only works when the Handset is in use.

TONE/PULSE SETTING

Your VT 9152 is factory preset for TONE dialing. If you require PULSE (ROTARY) dialing, press PROG/MEM, *, #, PROG/MEM to switch to Pulse dialing. To go back to TONE dialing, press PROG/MEM, *, *, PROG/MEM.

TEMPORARY TONE

If you have rotary (Pulse) service, this feature allows you to enter Tone dialing mode easily. After making your call, simply press the *TONE key. You are now dialing in TONE mode. Once you press OFF to end your call, your Handset will revert to Pulse dialing mode.

RINGER PROGRAMMING

You can choose among 4 ring styles. You can also turn the Handset ringer off.

•Press PROG/MEM

•Press #

•Press 1,2,3 or 4 to hear the various styles; or press 5 to turn the Handset ringer off

•Press PROG/MEM to confirm your choice

CHECKING THE RINGER

•Press PROG/MEM

•Press #

•Press 0

•Press PROG/MEM to exit

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents
Table of Contents Additional Information Important Safety Instructions Introduction Parts Check ListReplacing the Handset Batteries Recharging the Battery PackGetting Started Getting Started Setting UP Your VT Wall Mounting Handset Features and Keys Getting Started Base Unit Features and Keys Getting Started Basic Operation Using Your VT 9152 Cordless Telephone Basic Operation USE the VT 9152 Handset to Program Your Answering System Basic Operation Answering System OperationIntroduction Call Screening from Base UnitHandset Layout for Answering System Operation KEY FunctionAnswering System Setup Checking DAY and Time SET Base RingerSET Number of Rings Recording a MemoPlayback of GREETINGS, Messages and Memos To Hear Your Outgoing GreetingRemote Commands Remote Operation of Your VT 9152 Answering SystemBelt Clip Headset OperationOperation Phone DOESN’T Work AT ALL Handset does not Ring When YOU Receive a CallCase of Difficulty No Dial ToneYour Answering System is not Recording Messages YOU Hear Other Calls While Using Your PhoneYour Caller Fades in and OUT Answer ON/OFF Light on the Base Unit is BlinkingHow long is the limited warranty period? Limited Warranty StatementWhat does this limited warranty cover? What is not covered by this limited warranty?How do you get warranty service? Other limitationsFCC Part FCC and IC RegulationsIC Industry Canada Rbrc R Seal Maintenance Taking Care OfyourtelephoneTechnical Specifications Page Issued
Related manuals
Manual 28 pages 3.99 Kb