VTech VT 9152 important safety instructions Answering System Setup

Page 14

ADVANCED OPERATION

ANSWERING SYSTEM SETUP

Before using your VT 9152 Answering System, follow these programming steps:

1 SET OUTGOING MESSAGE

Record your greeting to be heard by callers. If you do not record a greeting, your VT 9152 will play a default greeting.

•Press ANS. MACHINE on the Handset

•Press 4 (MENU). The voice prompt says “Set Outgoing Message”.

•Press 7 (Record). The voice prompt says “Now Recording”, followed by a beep. Speak into the Handset to record your announcement. Press 2 (Stop) when done.

Your recorded announcement will be played for you.

2 SET SECURITY CODE

Your 2 digit security code gives you access to your VT 9152 Answering System from a telephone at a different location. Factory preset to 19, your security code can be any number, from 00 to 99.

•Press ANS. MACHINE on the Handset

•Press 4 (MENU) twice, until you hear: “Set Security Code”.

•Press 6 (SELECT) to increment the security code by one per each press. Press 9 to increment by 10.

•Press 5 (SET) to confirm your security code selection. You can either press 4 (MENU) to continue programming, or OFF to exit programming.

3 SET DAY & TIME

•Press ANS. MACHINE on the Handset.

•Press 4 (MENU) three times. You will hear: “Set Day and Time”.

•Press 6 (SELECT) until hear the correct day; then press 5 (SET).

•Press 6 (SELECT) until you hear the correct hour, then press 5 (SET).

•Press 6 (SELECT) until you hear the correct minute (or press 9 to increment the minutes by 10), then press 5 (SET). You can now either press 4 (MENU) to continue programming, or OFF to exit.

4 SET AUDIBLE MESSAGE ALERT

This feature provides a beep tone at the Base Unit every 10 seconds, alerting you to new messages.

•Press ANS. MACHINE on the Handset.

•Press 4 (MENU) four times. You will hear: “Set Audible Message Alert”.

•Press 6 (SELECT) to toggle between On and Off.

•Press 5 (SET) to confirm your selection.

•Press 4 (MENU) to continue programming, or OFF to exit.

5 SET ANNOUNCE ONLY

Your VT 9152 Answering System can also play your greeting, without taking messages from callers. In this case, ANNOUNCE ONLY is set to ON.

•Press ANS. MACHINE on the Handset.

•Press 4 (MENU) five times. You will hear: “Set Announce Only”.

•Press 6 (SELECT) to toggle between On and Off.

•Press 5 (SET) to confirm your selection.

•Press 4 (MENU) to continue programming, or OFF to exit.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Table of Contents Additional Information Important Safety Instructions Introduction Parts Check ListGetting Started Recharging the Battery PackReplacing the Handset Batteries Getting Started Setting UP Your VT Wall Mounting Handset Features and Keys Getting Started Base Unit Features and Keys Getting Started Basic Operation Using Your VT 9152 Cordless Telephone Basic Operation USE the VT 9152 Handset to Program Your Answering System Basic Operation Answering System OperationIntroduction Call Screening from Base UnitHandset Layout for Answering System Operation KEY FunctionAnswering System Setup Checking DAY and Time SET Base RingerSET Number of Rings Recording a MemoPlayback of GREETINGS, Messages and Memos To Hear Your Outgoing GreetingRemote Commands Remote Operation of Your VT 9152 Answering SystemOperation Headset OperationBelt Clip Phone DOESN’T Work AT ALL Handset does not Ring When YOU Receive a CallCase of Difficulty No Dial ToneYour Answering System is not Recording Messages YOU Hear Other Calls While Using Your PhoneYour Caller Fades in and OUT Answer ON/OFF Light on the Base Unit is BlinkingHow long is the limited warranty period? Limited Warranty StatementWhat does this limited warranty cover? What is not covered by this limited warranty?How do you get warranty service? Other limitationsIC Industry Canada FCC and IC RegulationsFCC Part Rbrc R Seal Maintenance Taking Care OfyourtelephoneTechnical Specifications Page Issued
Top Page Image Contents