VTech ia5829 manual Operating Range General, Conference calls

Page 47

9.Hit "Ok". Now "line or Line In" should show up in the master volume control for Recording. Please make sure that there is a check mark in the Select box under the "Line or Line IN

10.Go to Options and Select Properties.

11.There should be an option to adjust Recording or playback volume control. Choose Playback.

12.There is another section under playback where you pick which volume controls you want to show on the bar. Make sure there is a check next to "line or Line in". If there is not, please check it.

13.Hit "Ok". Now "line or Line in " should show up in the master volume control for Playback. Please make sure that there is a check mark in the MUTE box under the "line or line in". (it is possible that you may not have a MUTE option, it might be "SELECT". If you have a choice to SELECT then do not check SELECT under LINE")

14.Now close the Master Volume Control.

Operating Range General

This cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance --- which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright.

If you receive a call while you are out of range, the handset might not ring --- or if it does ring, the call might not connect when you press [PHONE]. Move closer to the base, then press [PHONE] to answer the call.

If you move out of range during a phone conversation, you might hear noise or interference. To improve reception, move closer to the base.

If you move out range without pressing[OFF], your phone will be left "off the hook." To hang up properly, walk back into range, periodically pressing [OFF].

Handset De-Registration (2455/2461)

1.Disconnect power to the Base (either unplug the DC connector from the bottom of the Base or unplug the power supply from the outlet). Remove spare battery, if applicable. 2.Hold down the base PAGE key while applying power back to the Base. When the POWER LED begins to blink, release the PAGE key.

THE USER HAS 15 SECONDS TO BEGIN THE NEXT STEP;OTHERWISE, THE BASE WILL EXIT PROGRAM MODE.

3.Hold down the PAGE key for 5 seconds. The HANDSET CHARGING LED will be lit, and after 5 seconds, the LINE IN USE LED will start to flash. Now release the PAGE key.

4.The HANDSET CHARGING LED will blink 5 times and then go out. Within 5 seconds from when it stops blinking, press and release the PAGE key.

All handsets should now be deregistered.

Conference calls

When call is conferenced, two lines are being bridged through one telephone. The normal loss that occurs between a station to station call is doubled when using the conference call feature. The quality of transmission depends on many variables including the amount

Image 47
Contents Page Table of Contents Headset Operation About Call History Review Call HistoryImportant Safety Instructions Important Safety Instructions Parts Check List Before You BeginLCD Handset LayoutBase Unit Layout Installation and Charge of Battery Started Setup GettingConnecting Power to Base Unit Getting Started Battery Care and MaintenanceConnecting to Phone Line Wall Mounting Getting Started SetupSet Date and Time CID Telephone OperationBasic Operation Handset OperationPage/Handset Lo- cator Base Operation Message Waiting IndicatorUse/Charging Indicator Telephone Operation Basic OperationMessage Waiting Handset Ringer Style/Battery SaveSet the Dial Mode Temporary Tone DialingDisplay Screen Messages Basic Operation Telephone OperationClear Message Waiting Alert Store a Number/Name in Speed Dial Memory Speed Dial MemoryDelete a Number/Name Stored in Memory Basic Operation Telephone MemoryEdit a Number/Name Stored in Memory Reassign Locations in Memory Dial a Memory NumberStore a Number/Name in the Directory Basic Operation Telephone DirectorySetting Move a Number/Name to the Memory Dial a Number from the DirectoryDelete Records from Call History Caller ID OperationAbout Call History Caller ID Review Call HistoryStore a Call History Record in the Directory Basic Operation Caller ID OperationDial a Displayed Number Belt Clip Headset OperationMaintenance Phone doesnt work at all Handset does not ring when you receive a callYou hear other calls while using your phone Case of DifficultyCommon cure for electronic equipment What is not covered by this limited warranty? Warranty StatementWhat does this limited warranty cover? How long is the limited warranty period?Other Limitations How do you get warranty service?FCC Part FCC, Acta and IC RegulationsRepair instructions Programming/testing of emergency numbersProduct identifier and REN information Connection and use with the nationwide telephone networkIC Industry Canada M I N a L E F F E C T I V E Range Technical SpecificationsIssued Need HELP? Cordless Troubleshooting Tags De-register and register Keypad Tone Feature Vtech Telephones Keypad Tone Feature 2256/1256 2325/2365 Replace Adjust Ringer VolumeRinger On/Melody Selection Process for T2406 calls SwitchDe-Register Process for gz2434 CallsTurning Message Light Off Language Conversion Twisted Pair CordsDual-Band Frequency Language Conversion of Base Menus English Spanish VT2461 Mk1 Deregister ALL Handsets Inch 4 conductor line cord VT2461 Mk1 Deregister a Single HandsetVT2461 Mk2a Deregistration process for Access to SoundCardConference calls Operating Range GeneralSpread Spectrum Echo Caller ID/Call Waiting ServicesCaller Id after 2nd ring Operating RangeDate Code Sticker Volume ControlsCardiac Pacemakers Crosstalk ToneLengthHandset Warmth Relocate Phone In Home EMI + Sep/PhnsHearing Aid Compatibility Clean Charging ContactsCall Waiting disconnects answering system External AntennasRecradle unplug AC Handset Locked Up BatteryCalling in same Area Code Chirping Sounds Common CureBase Unit Locked Up Single Audio Path MutesExplain Call Waiting Ringer Volume Not AdjustableLow Battery indicator Conductor Line CorfdDigital Voice Ringer EquivalenceJulian Date