VTech IA5879 manual Speed dial, Store a speed dial entry

Page 16

The entries you store in speed dial memory are marked from 01 to 09 and also displayed in the directory..

Press and hold PROG anytime to exit speed dial mode..

When the memory is full, the screen displays

MEMORY FULL, an error tone sounds and you cannot store

a new number until you delete a record from speed dial memory or the directory..

Speed dial

Your phone can store up to nine telephone numbers with names (up to 15 characters and 24 digits in each location) in the speed dial memory locations you assign (numbered 1 through 9) in each handset.. These numbers can be dialed with the pressing of two buttons presses.. You can also store telephone numbers with names alphabetically in the directory.. See Telephone Directory for instructions..

Store a speed dial entry

1..Press PROG on the handset.. Then press or until the screen displays SPEED DIAL.

2..Press SEL/INT.. The screen displays ENTER 1-9..

3.Press the key (1 through 9) to assign the speed dial location this number will be stored.. The screen displays ENTER NAME..

4.Using the chart below, enter up to 15 characters for the name you’re storing.. Use to backspace and make corrections; use to advance and add a space..

Presses

Dial key Once Twice 3 times 4 times 5 times 6 times

11

2

A

B

C

2

 

3

D

E

F

3

 

4

G

H

I

4

 

5

J

K

L

5

 

6

M

N

O

6

 

7

P

Q

R

S

7

8

T

U

V

8

 

9

W

X

Y

Z

9

00

*

*

 

 

 

 

 

#

&

,

-

..

#

16

www.vtechphones.com

Image 16
Contents Table of contents Battery care and performance Replace handset battery Additional informationNeed HELP? VTech toll free 1-800-595-9511 In Canada dialBefore you begin Parts check listInstall handset battery InstallationChoose a location Power connection Telephone line connectionData port Desk bracketCharge the handset battery Press SEL/INT to saveSet handset date and time Handset ringer/battery saveBase ringer If you subscribe to DSL service Belt clip optionalTelephone operation Handset operationBase operation ContrastThree way conference call Four way conference callTemporary tone dialing Message waitingOperating range Headset jackPeriodically pressing LINE1 or LINE2 Display screen messages Speed dial Store a speed dial entryEdit a speed dial entry Calling from speed dial Delete a speed dial entryReassigning locations in speed dial Store a directory entry in the handset DirectoryEdit a directory entry in the handset Delete a directory entry in the handset Dial a directory entry from the handset Store a speed dial entry in the directory from the handsetWill be displayed with this entry Directory memory capacity at the base Store a number in the directory at the baseStore a redial number in the directory at the base Dial from the directory at the baseDelete a directory entry at the base Replace a directory entry at the baseCaller ID About caller ID Review call historyDial a number from call history Delete a record from call historyStore a call history number in the directory Other party is blocking name and/or number InformationYour phone company is unable to receive information About this caller’s name and/or numberBattery care and performance Replace the handset batteryBattery needs charging when BatteriesTroubleshooting Handset to its base when not in useAllow up to one minute for the handset and base to reset ManualNoise Hold a charge Handset to its base when not in use S p l a y s o n m yComputers, kitchen appliances and other cordless phones Batteries will notInstalled in a low area Get noise, static, or’m near the base Outlet or near the microwaveTo another location, preferably to a higher floor Try unplugging some of the other phonesKitchen appliances and other cordless phones Near the microwave A low areaMy Caller ID isn’t For this to take placeMaintenance WarrantyAdditional Important safety instructions FCC, Acta and IC regulations FCC Part 68 and ActaRbrc seal Technical specifications Index Index 91-000570-010-000 User’s Manual