VTech CS6419-15 Battery charging, Battery indicators Battery status Action, Charger, LOW Battery

Page 8
SET DATE --/--/--

Getting started

Battery charging

Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 10 hours of continuous charging. See the table on page 37 for battery operating times.

If the screen is blank, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. When the battery is low, the handset plays four short beeps and shows LOW BATTERY along with a flashing icon. When you are on a call in low battery mode, the handset plays four short beeps every 50 seconds.

The following table summarizes the battery charge indicators and actions to take.

Battery indicators

Battery status

Action

The screen is blank,

Battery has no charge

Charge without interruption

or shows PLACE IN

or very little charge. The

(at least 30 minutes).

CHARGER and

 

flashes.

handset cannot be used.

 

 

 

 

 

 

 

 

The screen shows

Battery has enough

Charge without interruption (at

LOW BATTERY and

charge to be used for a

least 30 minutes).

 

 

flashes.

short time.

 

 

 

 

 

 

 

 

The screen shows

Battery is charged.

To keep the battery charged,

HANDSET X.

 

place it in the telephone base

 

 

 

 

 

 

or charger when not in use.

If you place the handset in the telephone base or charger without plugging in a battery, the screen displays NO BATTERY.

After you install your telephone or power returns following a power outage, the handset will prompt you to set the date and time. For instructions, see

Set date and time on page 13. To skip setting the date and time, press OFF/CANCEL.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Online user’s manual Congratulations Table of contents Appendix IndexParts checklist Getting startedTelephone base and charger installation Battery installation Charge light remains on when chargingBattery charging Battery indicators Battery status ActionLOW Battery ChargerInstallation options Tabletop to wall mount installationWall mount to tabletop installation See Telephone base and charger installation onTelephone base layout USE lightFlash Handset layoutCharge light MENU/SELECT Dialing keysTelephone settings Using the menuRinger volume To enter the handset menuRinger tone LCD languageKey tone Clear voicemail indicatorsTo manually turn off these indicators Set date and time Dial mode Home area codeTelephone operation Mute Call waitingTemporary ringer silencing Temporary tone dialingRedial list Review and dial a redial entryStore a number from the redial list to the directory Delete a redial entryTo access the directory while on a call To access the call log while on a callTo access the redial list while on a call Chain dialingJoin a call in progress Find handsetTo join a call To start the paging toneINT Other Handset is Calling when you have twoIntercom Call transfer using intercom Answer an incoming call during an intercom callFrom this intercom call, you have the following options Directory About the directoryCreate a new directory entry Edit Number Review the directory Alphabetical searchDial a directory entry Edit a directory entrySpeed dial Store a speed dial entryDial a speed dial number Delete a speed dial entryInformation about caller ID with call waiting Caller IDAbout caller ID Call log Not Available AT this TimeReview and dial from the call log Missed call indicatorMemory match View dialing options Save a call Iog entry to the directoryDelete from the call log Call log display screen messagesTo delete one entry To delete all entriesAppendix Handset display screen messagesTelephone number you have entered is already stored Handset and telephone base indicators On when the handset speakerphone is in useHandset lights Telephone base lightsBattery Battery needs charging whenTo register a handset Expand your telephone systemAdd and register a handset optional Replace a handset To deregister all handsetsTroubleshooting My telephone does not work at allThere is no dial tone Cannot dial outCharge light is off LOW Battery shows on the handset screenTelephone does not ring when there is an incoming call My handset beeps and is not performing normally Registration Failed appears on the handset Hear other calls when using the telephoneHear noise on the cordless handset and the keys do not work My caller ID features are not working properly Caller ID entries do not match the numbers I need to dialOUT of Range or no PWR AT Base shows in the handset screen NEW Voicemail and show on the display and I don’t know whyCommon cure for electronic equipment Important safety instructions Pacemaker patients Precautions for users of implanted cardiac pacemakersOperating range Maintenance Avoid rough treatmentAbout cordless telephones Rbrc sealLimited warranty What does this limited warranty cover?How long is the limited warranty period? What is not covered by this limited warranty?How do you get warranty service? Other limitationsFCC Part 68 and Acta FCC, Acta and IC regulationsFCC Part Industry Canada Technical specifications Index Index
Related manuals
Manual 16 pages 26.48 Kb
Top Page Image Contents