VTech I5808 manual ToneLength, Handset Warmth, Relocate Phone In Home EMI + Sep/Phns, Crosstalk

Page 16

940101B2-7CPS2A (CRS will not accept a slash.)

The battery save feature will deactivate the ring approximately 60 seconds after being set. After 60 seconds, the phone will enter "sleep mode". The phone will not ring or display "incoming call" when the extension phones are ringing. If any button on the phone is pressed, this will "wake up" the phone. If there is an incoming call within 60 seconds of a button being pressed, the phone will ring. Once nothing has been pressed for another 60 seconds, the phone will go back into "sleep mode" and will not ring.

ToneLength

Tone length for most cordless telephones is 80-100 milliseconds.

Some services may require longer tones. You need to look for a phone that will continue to produce a tone signal for as long as a digit is held down. We have many phones with long tones.

Handset Warmth

It is normal to feel heat near the battery compartment on the cordless handset once the battery has been fully charged. There is a component in the battery known as a "separator" which converts excess energy to heat.

Relocate Phone In Home EMI + Sep/Phns

Interference generated by some radio equipment and electrical appliances and machinery may travel through the air, affecting other types of equipment in close proximity.

Filters cannot help in this situation. Separating the objects may be the only solution. Split Line w/Triplex + Verify 2 cond cord on line 1

If single line telephone equipment is also experiencing crosstalk, the customer may try the following remedies:

1.Use shortest line cords possible.

2.Use 2 conductor line cords to connect all single line equipment. 3.Disconnect line 2 wires on any jack where not needed.

Crosstalk

If crosstalk occurs while phones are plugged into the network interface, inside wiring is NOT the problem. Plug separate phones into the individual interfaces for each line. Both lines will need to be in use at the same time to get valid test results.

TWO SINGLE LINE JACKS

Verify that 2 conductor line cord is connected to L1/L2 port on telephone. 4 conductor cord may be used at L2 port.

SINGLE LINE TELEPHONE EQUIPMENT

If single line telephone equipment is also experiencing crosstalk, customer may try the following remedies:

1.Use shortest line cords possible.

2.Use 2 conductor line cords to connect all single line equipment. 3.Disconnect line 2 wires on any jack where not needed.

TWO-LINE JACKS

·Use triplex adapter and 2 line cords at each affected two-line set.

·Connect cords to L1 and L2 on adapter (not L1+L2) cannot use wall phones with triplex adapter.

Suggestions for reducing local telephone line recordings:

Image 16
Contents Page Cordless Troubleshooting Tags De-register and register Keypad Tone Feature Vtech Telephones Keypad Tone Feature Ringer On/Melody Selection Adjust Ringer Volume2256/1256 2325/2365 Replace Switch Process for T2406 callsTurning Message Light Off Process for gz2434 CallsDe-Register Dual-Band Frequency Twisted Pair CordsLanguage Conversion Language Conversion of Base Menus English Spanish VT2461 Mk1 Deregister ALL Handsets VT2461 Mk2a VT2461 Mk1 Deregister a Single HandsetInch 4 conductor line cord Access to SoundCard Deregistration process forOperating Range General Conference callsCaller ID/Call Waiting Services Caller Id after 2nd ringOperating Range Spread Spectrum EchoCardiac Pacemakers Volume ControlsDate Code Sticker ToneLength Handset WarmthRelocate Phone In Home EMI + Sep/Phns CrosstalkClean Charging Contacts Call Waiting disconnects answering systemExternal Antennas Hearing Aid CompatibilityCalling in same Area Code Handset Locked Up BatteryRecradle unplug AC Common Cure Base Unit Locked UpSingle Audio Path Mutes Chirping SoundsRinger Volume Not Adjustable Low Battery indicatorConductor Line Corfd Explain Call WaitingJulian Date Ringer EquivalenceDigital Voice Table of Contents Important Safety Instructions Important Safety Instructions Introduction Getting Started Parts Check List Handset Layout GettingStatartedGetting Started Setup Installation and Charge of Battery in HandsetBattery Life GettingStartedInstallation and Registration of Accessory Handset Getting Started RegistrationBasic Operation Handset IndicatorsHandset LEDs Advance Operation Headset OperationBelt Clip Maintenance Handset does not ring when you receive a call Case Of DifficultyPhone doesnt work at all No dial toneYour Handset vibrates or shakes when a call comes You hear other calls while using your phoneCommon cure for electronic equipment You cannot hear recorded messagesWarranty Statement What does this limited warranty cover?How long is the limited warranty period? What is not covered by this limited warranty?How do you get warranty service? Other LimitationsFCC, Acta and IC Regulations FCC PartProduct identifier and REN information Connection and use with the nationwide telephone networkRepair instructions Rights of the telephone companyHearing aid compatibility Programming/testing of emergency numbersIC Industry Canada FCC, Acta and IC Regulations Technical Specifications HandsetIssue Need HELP?