VTech I5808 manual Cordless Troubleshooting Tags De-register and register

Page 2

CORDLESS Troubleshooting TAGS

250 De-register and register

De-register handset from the E2525, E2600B and E2555

Please take the Handset out of the Base before de-registering. Using the [SOFT] Keys on the Base, press MENU, then press the Down arrow twice until BASE SETTINGS is highlighted. Press OK, then press MUTE 3 times and FLASH twice. This will deregister the unit, please see more info to re-register.

Adding Handsets / Registering Handsets

Your telephone can accommodate up to 8 cordless Handsets. You can add new Handsets (Model E250, sold separately) at any time, but each must be registered with the Base before use.

Before using a new Handset, you must register it with the Base. There will be an R in the upper left hand corner of the display. The Display will read "ENTER BASE ID". Use the keypad on the Handset to enter Base ID. (To find this number, go to the Base, press [MENU], scroll down to select DISPLAY BASE ID, then press OK.) Once you have entered the Base ID number, press OK (middle key under the display). The unit will display "SEARCHING FOR BASE" and then "FOUND BASE". Your Handset will then be ready to use.

The Handset provided with your telephone is automatically registered as Handset 1. Additional Handsets will be assigned numbers in the order the are registered (2, 3, 4, etc.) up to a maximum of eight.

De-register 250 from the E2520 Base

Take the Handset out of the Base, press [*] [*] [3] [3] [5] [7] [8] [2] on the Base. This will de-register all of the Handsets at one time. See more information to register them again.

NOTE: The Base ID code is located on the bottom of the Base. Adding new Handsets / registering the Handset

Your telephone can accommodate up to 8 cordless Handsets. You can add new Handsets (Model E250, sold separately) at any time, but each must be registered with the Base before use.

Before using a new Handset, you must register it with the Base. There will be an R in the upper left hand corner of the Display. The Display will read "ENTER BASE ID". Use the keypad on the Handset to enter the Base ID. (To find this number, go to the Base, on the bottom of the Base will be a white sticker that reads BS ID CODE. The code will start with a 36. Once you have entered the Base ID number, press OK (middle key under the display). The unit will display "SEARCHING FOR BASE" and then "FOUND BASE". Your Handset will then be ready to use.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Page Cordless Troubleshooting Tags De-register and register Keypad Tone Feature Vtech Telephones Keypad Tone Feature 2256/1256 2325/2365 Replace Adjust Ringer VolumeRinger On/Melody Selection Switch Process for T2406 callsDe-Register Process for gz2434 CallsTurning Message Light Off Language Conversion Twisted Pair CordsDual-Band Frequency Language Conversion of Base Menus English Spanish VT2461 Mk1 Deregister ALL Handsets Inch 4 conductor line cord VT2461 Mk1 Deregister a Single HandsetVT2461 Mk2a Access to SoundCard Deregistration process forOperating Range General Conference callsOperating Range Caller ID/Call Waiting ServicesCaller Id after 2nd ring Spread Spectrum EchoDate Code Sticker Volume ControlsCardiac Pacemakers Relocate Phone In Home EMI + Sep/Phns ToneLengthHandset Warmth CrosstalkExternal Antennas Clean Charging ContactsCall Waiting disconnects answering system Hearing Aid CompatibilityRecradle unplug AC Handset Locked Up BatteryCalling in same Area Code Single Audio Path Mutes Common CureBase Unit Locked Up Chirping SoundsConductor Line Corfd Ringer Volume Not AdjustableLow Battery indicator Explain Call WaitingDigital Voice Ringer EquivalenceJulian Date Table of Contents Important Safety Instructions Important Safety Instructions Introduction Getting Started Parts Check List Handset Layout GettingStatartedGetting Started Setup Installation and Charge of Battery in HandsetBattery Life GettingStartedInstallation and Registration of Accessory Handset Getting Started RegistrationHandset LEDs Handset IndicatorsBasic Operation Belt Clip Headset OperationAdvance Operation Maintenance Phone doesnt work at all Handset does not ring when you receive a callCase Of Difficulty No dial toneCommon cure for electronic equipment Your Handset vibrates or shakes when a call comesYou hear other calls while using your phone You cannot hear recorded messagesHow long is the limited warranty period? Warranty StatementWhat does this limited warranty cover? What is not covered by this limited warranty?How do you get warranty service? Other LimitationsFCC, Acta and IC Regulations FCC PartRepair instructions Product identifier and REN informationConnection and use with the nationwide telephone network Rights of the telephone companyIC Industry Canada Programming/testing of emergency numbersHearing aid compatibility FCC, Acta and IC Regulations Technical Specifications HandsetIssue Need HELP?
Top Page Image Contents