VTech I5808 manual Operating Range General, Conference calls

Page 13

9.Hit "Ok". Now "line or Line In" should show up in the master volume control for Recording. Please make sure that there is a check mark in the Select box under the "Line or Line IN

10.Go to Options and Select Properties.

11.There should be an option to adjust Recording or playback volume control. Choose Playback.

12.There is another section under playback where you pick which volume controls you want to show on the bar. Make sure there is a check next to "line or Line in". If there is not, please check it.

13.Hit "Ok". Now "line or Line in " should show up in the master volume control for Playback. Please make sure that there is a check mark in the MUTE box under the "line or line in". (it is possible that you may not have a MUTE option, it might be "SELECT". If you have a choice to SELECT then do not check SELECT under LINE")

14.Now close the Master Volume Control.

Operating Range General

This cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance --- which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright.

If you receive a call while you are out of range, the handset might not ring --- or if it does ring, the call might not connect when you press [PHONE]. Move closer to the base, then press [PHONE] to answer the call.

If you move out of range during a phone conversation, you might hear noise or interference. To improve reception, move closer to the base.

If you move out range without pressing[OFF], your phone will be left "off the hook." To hang up properly, walk back into range, periodically pressing [OFF].

Handset De-Registration (2455/2461)

1.Disconnect power to the Base (either unplug the DC connector from the bottom of the Base or unplug the power supply from the outlet). Remove spare battery, if applicable. 2.Hold down the base PAGE key while applying power back to the Base. When the POWER LED begins to blink, release the PAGE key.

THE USER HAS 15 SECONDS TO BEGIN THE NEXT STEP;OTHERWISE, THE BASE WILL EXIT PROGRAM MODE.

3.Hold down the PAGE key for 5 seconds. The HANDSET CHARGING LED will be lit, and after 5 seconds, the LINE IN USE LED will start to flash. Now release the PAGE key.

4.The HANDSET CHARGING LED will blink 5 times and then go out. Within 5 seconds from when it stops blinking, press and release the PAGE key.

All handsets should now be deregistered.

Conference calls

When call is conferenced, two lines are being bridged through one telephone. The normal loss that occurs between a station to station call is doubled when using the conference call feature. The quality of transmission depends on many variables including the amount

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Cordless Troubleshooting Tags De-register and register Keypad Tone Feature Vtech Telephones Keypad Tone Feature Ringer On/Melody Selection Adjust Ringer Volume2256/1256 2325/2365 Replace Process for T2406 calls SwitchTurning Message Light Off Process for gz2434 CallsDe-Register Dual-Band Frequency Twisted Pair CordsLanguage Conversion Language Conversion of Base Menus English Spanish VT2461 Mk1 Deregister ALL Handsets VT2461 Mk2a VT2461 Mk1 Deregister a Single HandsetInch 4 conductor line cord Deregistration process for Access to SoundCardConference calls Operating Range GeneralCaller Id after 2nd ring Caller ID/Call Waiting ServicesOperating Range Spread Spectrum EchoCardiac Pacemakers Volume ControlsDate Code Sticker Handset Warmth ToneLengthRelocate Phone In Home EMI + Sep/Phns CrosstalkCall Waiting disconnects answering system Clean Charging ContactsExternal Antennas Hearing Aid CompatibilityCalling in same Area Code Handset Locked Up BatteryRecradle unplug AC Base Unit Locked Up Common CureSingle Audio Path Mutes Chirping SoundsLow Battery indicator Ringer Volume Not AdjustableConductor Line Corfd Explain Call WaitingJulian Date Ringer EquivalenceDigital Voice Table of Contents Important Safety Instructions Important Safety Instructions Introduction Getting Started Parts Check List GettingStatarted Handset LayoutInstallation and Charge of Battery in Handset Getting Started SetupGettingStarted Battery LifeGetting Started Registration Installation and Registration of Accessory HandsetBasic Operation Handset IndicatorsHandset LEDs Advance Operation Headset OperationBelt Clip Maintenance Case Of Difficulty Handset does not ring when you receive a callPhone doesnt work at all No dial toneYou hear other calls while using your phone Your Handset vibrates or shakes when a call comesCommon cure for electronic equipment You cannot hear recorded messagesWhat does this limited warranty cover? Warranty StatementHow long is the limited warranty period? What is not covered by this limited warranty?Other Limitations How do you get warranty service?FCC Part FCC, Acta and IC RegulationsConnection and use with the nationwide telephone network Product identifier and REN informationRepair instructions Rights of the telephone companyHearing aid compatibility Programming/testing of emergency numbersIC Industry Canada FCC, Acta and IC Regulations Handset Technical SpecificationsIssue Need HELP?
Top Page Image Contents