Cisco Systems WIP300 manual Sound Settings

Page 55

Wireless-G IP Phone

Option	Description
Call Waiting	Check to enable Call Waiting, uncheck to disable

Forward Number	Enter a phone number or IP address to forward your calls to

Forward All	Check to send all incoming calls to the Forward Number

No Answer	Check to send calls to Forward Number when there is no answer on the IP phone

Block Caller ID	Select On to block caller id’s that you previously set up in the IP phone menu

Refuse Private	Select On to refuse calls that display Private Call as the User ID

Busy	Check to forward calls when your phone is busy

Beep Notification	Enable or disable the Beep Notification feature. When this feature is enabled, the phone will beep
	every 50 seconds so that you can keep track of how long you’ve been on a call.

Hold Transfer	Select SIP or DTMF Flash as the method used for transferring calls

Regional Tone	Set the Regional tone setting to North America or Japan

Sound Settings

Click the Sound Settings tab to change the IP Phone’s speaker volume, ringer settings, and warning tones. Refer to the table below for a list of options available in the Sound Settings menu.

Option	Description

Speaker Volume	Set the IP Phone’s speaker volume

Melody	Choose one of the available ring tone melodies

Ring Volume	Set the IP Phone’s ring volume

Ring Mode	Set the IP Phone’s ring mode to Silent, Ring, Vibrate, or Ring + Vibrate

Warning Tone	Check to enable the IP Phone’s warning tones, such as low battery

46		Chapter 5: Using the Web-based Utility
		Settings

Image 55

Contents Wireless- G Page Copyright and Trademarks Table of Contents Appendix a Troubleshooting Wireless-G IP Phone Bottom Panel List of Figures15 Forwarding 67 Enter Register Proxy IP Welcome IntroductionWhat’s in This User Guide? Introduction What’s in This User Guide? Wireless-G IP Phone Bottom Panel Getting to Know the Wireless-G IP PhoneNavigation Button Front PanelSide Panel Back Panel Overview Installing and Using the Wireless-G IP PhoneCharging the IP Phone’s Battery Setting up the Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Using the Wireless-G IP Phone Home Screen Configuring the Wireless-G IP Phone Wireless-G IP PhonePhonebook Main MenuCall Log Mail Configuring Your AccountOption Description Write New Using the E-mail ClientOption Description Draft Speed DialNetwork Profile ProfileEditing a Network Profile Settings Following optionsSIP Account Configuring the Wireless-G IP Phone SIP Account Roaming Profile PasswordSettings Secure SetupLanguage Clock Alarm ClockCSpeed Dial Call SettingsDisplay Settings Sound SettingsKeypad IP Statistics Allows you to view network packets statistics ToolsHow to Access the Web-based Utility Using the Web-based UtilityStatus Using the Web-based Utility Phonebook E-mail screen Using the Web-based Utility Network Profile SIP Using the Web-based Utility Settings Sound Settings Display Settings Software Information SoftwareBootcode Information BootcodeReboot PasswordCommon Problems and Solutions Appendix a TroubleshootingApplication Start and End Protocol IP Address Enable Wireless-G IP Phone Wireless-G IP Phone Power LED does not light up Can I receive calls while my network is down? Frequently Asked QuestionsAppendix B Glossary Appendix B Glossary Wireless-G IP Phone Wireless-G IP Phone TCP/IP Appendix C SpecificationsStorage Humidity 10% to 95% Non-Condensing Limited Warranty Appendix D Warranty InformationAppendix D Warranty Information FCC Statement Appendix E Regulatory InformationAppendix E Regulatory Information Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Wireless-G IP Phone Appendix F Contact Information Appendix F Contact Information