Telex BTR-800 dimensions 704.700, TR-825 Menu Structure Transmit Screen

Page 60

TR-825 Menu Structure

Transmit Screen

Transmit Screen

The Transmit screen allows the user to set the beltpack trans- mit frequency. Factory-defined groups will allow only a set number of pre -defined frequen cies to be se lected . User-programmable groups will allow the user to change the frequency in 25kHz steps.

•Press [MENU] once from the group/channel screen to ar- rive at the transmit frequency screen.

TX

704.700

[SET]

•

•

•

•

Press [SET] to edit the frequency. The number will start flashing. Factory-defined groups will allow only a set number of pre-defined frequencies to be selected. User-programmable groups will allow the user to change the frequency in 25kHz steps.

Use the [UP]/[DOWN] arrow buttons to change the fre- quency.

Press [SET] to place the beltpack on the frequency se- lected. If set is held down, during that time the group/channel is displayed so the user is aware of what transmit channel the unit has been placed. Once set is re- leased, the unit returns to the transmit frequency screen with nothing flashing.

Pressing [SET] once more will start the editing sequence over again. Pressing [MENU] during transmit frequency edit will end editing and send the user back to the transmit screen without any changes.

TX

704.700

[UP]/[DOWN]

TX

706.500

[SET] IS HELD DOWN

03A 03

GP CH

[SET] IS RELEASED

TX

706.500

END

7-25

Image 60

Contents JTN Telex Thank you for choosing RadioComTM Table of Contents Tech Tips System Features IntroductionGeneral Description BTR-800 Block Diagram WTA aLocal Headset Wiring BTR-800 Base StationControls and Connections Front Panel BTR-800 Front PanelControls and Connections Rear Panel BTR-800 Rear PanelBTR-800 Specifications OverallBlank TR-800 Beltpack Controls and Connections Top PanelTR-800 Top Panel TR-800 Rear Panel/Connector/Antennas Push-to-Talk/Push-to-Transmit SwitchHeadset Jack Wiring LCD Liquid Crystal DisplayTR-800 Specifications Blank TR-825 Beltpack Telex RAAudio + Audio a Switched Headphone Ground TR-825 Rear Panel/Connector/AntennasTR-825 Specifications Blank Initial Equipment Set-Up UnpackingBTR-800 TR-800, TR-825Antenna Placement Antenna ConnectionAntenna Polarization Distance between AntennasDistance Between base station and beltpack Operating System Near ObstructionsKeeping Site Clear to Antenna Antenna Placement Improving Reception and Increasing RangePower Connection Transmit SwitchesBase Station Set-up LocationInternal Transmit Switches Intercom SwitchInternal Transmit Switches RJ-11 Type/ Four-wire PinoutRTS Distribution Panel TW5W Example Interface to an RTS TW SystemParts to be Removed by User to Enable Dual Listen Dual Listen FunctionalityAudio Board Part Number and Dual Listen Component Locations Internal Auxiliary Input Routing Switch Auxiliary Input Routing SwitchAuxiliary Input/Output Relay Output Schematic Stage Announce / Relay ContactsRelay Contact Jack Adapter Screw Terminal Adapter Internal Stage Announce Level ControlBase Station Link Two Stand Alone Base Stations Connected TogetherBase Station Link Cable Beltpack Set-up Battery Installation Charger and battery pack damageBattery Installation May resultTransmit mode Headset ConnectionTR-800 and TR-825 Rear Panel Push-to-Talk PT Talk Recommended positionBlank Pre-Walk-Thru Checklist Blank System Operation Frequency Plan OverviewSystem Quick Start Factory-Defined GroupsPower Base Station OperationLocal Headset Intercom a and BDisplay Contrast LCD ContrastBTR-800 Menu Structure Main Screen Flowchart Power-Up Screen Operating ScreenBeltpack Activity Code Definitions Group / Channel Select UP / DownSET Last Rx Changed Group / Frequency Select Frequency Edit User-Programmed Groups OnlyClearScanTM ClearScan1st Use Default Factory DefaultSpecial Key Sequences Lockout CopyBeltpack Operation TR-800 and TR-825 Top and Rear PanelBeltpack Feature Enable/Disable Menus TR-800 Menu Structure Beltpack Menu StructureTR-800 Menu Structure Power-Up Screens Power-Up ScreensTR-800 Menu Structure Group / Channel Screen Group / Channel ScreenTR-800 Menu Structure Transmit Screen Transmit ScreenTR-800 Menu Structure Receive 1 Screen Receive 1 ScreenTR-800 Menu Structure Receive 2 Screen Receive 2 ScreenTR-800 Menu Structure ClearScan ClearScanTR-800 Menu Structure Stage Announce Enable/Disable Wireless Talk Around Enable/DisableTR-800 Menu Structure Audio Channel a or B Disable/Enable Talk Button Latch on/Latch offTR-800 Menu Structure Special Key Sequences Lockout 04A Scn TR-825 Menu Structure Beltpack Menu StructureTR-825 Menu Structure Power-Up Screens TR-825 Menu Structure Group / Channel Screen 704.700 TR-825 Menu Structure Transmit ScreenTR-825 Menu Structure Receive 1 Screen TR-825 Menu Structure Receive 2 Screen Ab SEP TR-825 Menu Structure Audio Output04b TR-825 Menu Structure ClearScanTMTR-825 Menu Structure Stage Announce Enable/Disable SA onTR-825 Menu Structure Wireless Talk Around TA bTR-825 Menu Structure Audio Channel a Options Audio Channel a OptionsTR-825 Menu Structure Audio Channel B Options Hold SET and Press B Continue to Hold SET Press B AgainTR-825 Menu Structure Special Key Sequences Lockout System Walk-Thru Blank Troubleshooting Problem SolutionBlank Microphone Gain Adjustment Tech TipsFrequency Interaction Blank Battery Information Battery Life TR-800TR-825 Blank Intercom Systems Specifications CommonBlank Accessories and Replacement Parts Blank Software License End-User License Agreement for Telex SoftwareBlank Certification Information FCC LicensingEU Declaration of Conformity PN 803257-1 Rev. H March Made in U.S.A