Telex TR-825, BTR-800 dimensions Certification Information, FCC Licensing

Page 84

Section

15

Certification Information

FCC LICENSING

The Telex BTR-800, TR-800, and the TR-825 Transmitter/Receiver are Type Accepted under United States Federal Communications Commission Part 74. Licensing of Telex equipment is the User’s responsibility and licensibility depends on the user’s classification, users application, and frequency selected. Telex strongly urges the user to contact the appropriate telecommunications authority for any desired clarification.

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

CAUTION: Changes or modifications made by the user could void the user’s authority to operate the equipment.

Mandatory Safety Instructions

to Base Station Installers and Users

1.Use only manufacturer or dealer supplied antenna. Antenna minimum safe distance, as calculated from FCC requirements, is 4.8cm. However, the FCC default for the minimum safe distance is 20cm. Antenna gain: zero dBd referenced to a dipole.

2.The FEDERAL COMMUNICATIONS COMMISSION has adopted a safety standard for human exposure to RF (Radio Frequency) energy, which is below the OSHA (Occupational Safety and Health Act) limits.

3.To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the mini- mum safe distance show here, and in accordance with the requirements of the antenna manufacturer or supplier.

4.Antenna substitution: Do Not substitute any antenna for the one supplied by or recommended by the man- ufacturer or radio dealer. You may be exposing person or persons to harmful radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions.

5.WARNING: Maintain a separation distance from the antenna to person(s) of at least 20cm.

You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure that the minimum separation distance (above) is maintained between the antenna and nearby per- sons for satisfying RF Exposure compliance.

The operation of this transmitter must satisfy the requirements of the General Population/Uncontrolled Ex- posure Environment for work-related use. Transmit only when person(s) are at least the minimum dis- tance from the properly installed, externally mounted antenna.

OTHER CERTIFICATIONS

Versions of the BTR-800 and TR-800 which display the "CE" symbol on the unit are certified to

0891 ETSI EN 300 454-2, ETSI EN 301 489-9 and EN 60950 standards. These units conform to Euro pean Union directives, eligible to bear CE marking . See next page for the decla-

ration of conformity.

15-1

Page 83 Page 85
Image 84
Page 83 Page 85
Contents JTN Telex Thank you for choosing RadioComTM Table of Contents Tech Tips System Features IntroductionGeneral Description BTR-800 Block Diagram WTA aLocal Headset Wiring BTR-800 Base StationControls and Connections Front Panel BTR-800 Front PanelControls and Connections Rear Panel BTR-800 Rear PanelBTR-800 Specifications OverallBlank TR-800 Beltpack Controls and Connections Top PanelTR-800 Top Panel TR-800 Rear Panel/Connector/Antennas Push-to-Talk/Push-to-Transmit SwitchHeadset Jack Wiring LCD Liquid Crystal DisplayTR-800 Specifications Blank TR-825 Beltpack Telex RAAudio + Audio a Switched Headphone Ground TR-825 Rear Panel/Connector/AntennasTR-825 Specifications Blank Initial Equipment Set-Up UnpackingBTR-800 TR-800, TR-825Antenna Placement Antenna ConnectionAntenna Polarization Distance between AntennasDistance Between base station and beltpack Operating System Near ObstructionsKeeping Site Clear to Antenna Antenna Placement Improving Reception and Increasing RangePower Connection Transmit SwitchesBase Station Set-up LocationInternal Transmit Switches Intercom SwitchInternal Transmit Switches RJ-11 Type/ Four-wire PinoutRTS Distribution Panel TW5W Example Interface to an RTS TW SystemParts to be Removed by User to Enable Dual Listen Dual Listen FunctionalityAudio Board Part Number and Dual Listen Component Locations Internal Auxiliary Input Routing Switch Auxiliary Input Routing SwitchAuxiliary Input/Output Relay Output Schematic Stage Announce / Relay ContactsRelay Contact Jack Adapter Screw Terminal Adapter Internal Stage Announce Level ControlBase Station Link Two Stand Alone Base Stations Connected TogetherBase Station Link Cable Beltpack Set-up Battery Installation Charger and battery pack damageBattery Installation May resultTransmit mode Headset ConnectionTR-800 and TR-825 Rear Panel Push-to-Talk PT Talk Recommended positionBlank Pre-Walk-Thru Checklist Blank System Operation Frequency Plan OverviewSystem Quick Start Factory-Defined GroupsPower Base Station OperationLocal Headset Intercom a and BDisplay Contrast LCD ContrastBTR-800 Menu Structure Main Screen Flowchart Power-Up Screen Operating ScreenBeltpack Activity Code Definitions Group / Channel Select UP / DownSET Last Rx Changed Group / Frequency Select Frequency Edit User-Programmed Groups OnlyClearScanTM ClearScan1st Use Default Factory DefaultSpecial Key Sequences Lockout CopyBeltpack Operation TR-800 and TR-825 Top and Rear PanelBeltpack Feature Enable/Disable Menus TR-800 Menu Structure Beltpack Menu StructureTR-800 Menu Structure Power-Up Screens Power-Up ScreensTR-800 Menu Structure Group / Channel Screen Group / Channel ScreenTR-800 Menu Structure Transmit Screen Transmit ScreenTR-800 Menu Structure Receive 1 Screen Receive 1 ScreenTR-800 Menu Structure Receive 2 Screen Receive 2 ScreenTR-800 Menu Structure ClearScan ClearScanTR-800 Menu Structure Stage Announce Enable/Disable Wireless Talk Around Enable/DisableTR-800 Menu Structure Audio Channel a or B Disable/Enable Talk Button Latch on/Latch offTR-800 Menu Structure Special Key Sequences Lockout 04A Scn TR-825 Menu Structure Beltpack Menu StructureTR-825 Menu Structure Power-Up Screens TR-825 Menu Structure Group / Channel Screen 704.700 TR-825 Menu Structure Transmit ScreenTR-825 Menu Structure Receive 1 Screen TR-825 Menu Structure Receive 2 Screen Ab SEP TR-825 Menu Structure Audio Output04b TR-825 Menu Structure ClearScanTMTR-825 Menu Structure Stage Announce Enable/Disable SA onTR-825 Menu Structure Wireless Talk Around TA bTR-825 Menu Structure Audio Channel a Options Audio Channel a OptionsTR-825 Menu Structure Audio Channel B Options Hold SET and Press B Continue to Hold SET Press B AgainTR-825 Menu Structure Special Key Sequences Lockout System Walk-Thru Blank Troubleshooting Problem SolutionBlank Microphone Gain Adjustment Tech TipsFrequency Interaction Blank Battery Information Battery Life TR-800TR-825 Blank Intercom Systems Specifications CommonBlank Accessories and Replacement Parts Blank Software License End-User License Agreement for Telex SoftwareBlank Certification Information FCC LicensingEU Declaration of Conformity PN 803257-1 Rev. H March Made in U.S.A
Top Page Image Contents