Telex BTR-800 dimensions TR-825 Menu Structure Receive 1 Screen

Page 61

TR-825 Menu Structure

Receive 1 Screen

Receive 1 Screen

The Receive 1 screen allows the user to set the beltpack re- ceiver 1 frequency. This corresponds to the base station’s transmit 1 frequency. In factory-defined groups receiver 1 is not changeable. User-programmable groups will allow the user to change the frequency in 25kHz steps.

Press [MENU] twice from the group/channel screen to ar- rive at the receive 1 frequency screen.

(User-Programmable Groups Only) Press [SET] to edit the frequency. The number will start flashing. Fac-

tory-defined groups can’t be changed; so pressing set will do nothing at this screen. User-programmed groups will start flashing and allow the user to change the frequency in 25kHz steps.

( U s e r- P r o g r a mma b l e G r o u p s O n l y) U s e th e [UP]/[DOWN] arrow buttons to change the frequency.

(User-Programmable Groups Only) Press [SET] to place the beltpack on the frequency selected. If set is held

down, during that time the group is displayed so the user is aware of what group the unit has been placed. Once set is released, the unit returns to the receive 1 frequency screen with nothing flashing.

(User-Programmable Groups Only) Pressing [SET] once more will start the editing sequence over again. Pressing

[MENU] during receive 1 frequency edit will end editing and send the user back to the receive 1 screen without any changes.

R1

554.250

[SET]

R1

54.250

[UP] / [DOWN]

1

566.750

[SET] IS HELD DOWN

27u

GP

[SET] IS RELEASED

R1

566.750

END

7-26

Image 61
Contents JTN Telex Thank you for choosing RadioComTM Table of Contents Tech Tips Introduction System FeaturesGeneral Description WTA a BTR-800 Block DiagramBTR-800 Base Station Local Headset WiringControls and Connections Front Panel BTR-800 Front PanelBTR-800 Rear Panel Controls and Connections Rear PanelOverall BTR-800 SpecificationsBlank Controls and Connections Top Panel TR-800 BeltpackTR-800 Top Panel Push-to-Talk/Push-to-Transmit Switch TR-800 Rear Panel/Connector/AntennasHeadset Jack Wiring LCD Liquid Crystal DisplayTR-800 Specifications Blank Telex RA TR-825 BeltpackTR-825 Rear Panel/Connector/Antennas Audio + Audio a Switched Headphone GroundTR-825 Specifications Blank Unpacking Initial Equipment Set-UpBTR-800 TR-800, TR-825Antenna Connection Antenna PlacementAntenna Polarization Distance between AntennasOperating System Near Obstructions Distance Between base station and beltpackKeeping Site Clear to Antenna Improving Reception and Increasing Range Antenna PlacementTransmit Switches Power ConnectionBase Station Set-up LocationIntercom Switch Internal Transmit SwitchesInternal Transmit Switches RJ-11 Type/ Four-wire PinoutExample Interface to an RTS TW System RTS Distribution Panel TW5WDual Listen Functionality Parts to be Removed by User to Enable Dual ListenAudio Board Part Number and Dual Listen Component Locations Auxiliary Input Routing Switch Internal Auxiliary Input Routing SwitchAuxiliary Input/Output Stage Announce / Relay Contacts Relay Output SchematicRelay Contact Jack Adapter Screw Terminal Adapter Internal Stage Announce Level ControlTwo Stand Alone Base Stations Connected Together Base Station LinkBase Station Link Cable Charger and battery pack damage Beltpack Set-up Battery InstallationBattery Installation May resultHeadset Connection Transmit modeTR-800 and TR-825 Rear Panel Push-to-Talk PT Talk Recommended positionBlank Pre-Walk-Thru Checklist Blank Frequency Plan Overview System OperationSystem Quick Start Factory-Defined GroupsBase Station Operation PowerLocal Headset Intercom a and BLCD Contrast Display ContrastBTR-800 Menu Structure Main Screen Flowchart Operating Screen Power-Up ScreenBeltpack Activity Code Definitions UP / Down Group / Channel SelectSET Last Rx Changed Group / Frequency Select User-Programmed Groups Only Frequency EditClearScan ClearScanTMFactory Default 1st Use DefaultSpecial Key Sequences Lockout CopyTR-800 and TR-825 Top and Rear Panel Beltpack OperationTR-800 Menu Structure Beltpack Menu Structure Beltpack Feature Enable/Disable MenusPower-Up Screens TR-800 Menu Structure Power-Up ScreensGroup / Channel Screen TR-800 Menu Structure Group / Channel ScreenTransmit Screen TR-800 Menu Structure Transmit ScreenReceive 1 Screen TR-800 Menu Structure Receive 1 ScreenReceive 2 Screen TR-800 Menu Structure Receive 2 ScreenClearScan TR-800 Menu Structure ClearScanWireless Talk Around Enable/Disable TR-800 Menu Structure Stage Announce Enable/DisableTalk Button Latch on/Latch off TR-800 Menu Structure Audio Channel a or B Disable/EnableTR-800 Menu Structure Special Key Sequences Lockout TR-825 Menu Structure Beltpack Menu Structure 04A ScnTR-825 Menu Structure Power-Up Screens TR-825 Menu Structure Group / Channel Screen TR-825 Menu Structure Transmit Screen 704.700TR-825 Menu Structure Receive 1 Screen TR-825 Menu Structure Receive 2 Screen TR-825 Menu Structure Audio Output Ab SEPTR-825 Menu Structure ClearScanTM 04bSA on TR-825 Menu Structure Stage Announce Enable/DisableTA b TR-825 Menu Structure Wireless Talk AroundAudio Channel a Options TR-825 Menu Structure Audio Channel a OptionsHold SET and Press B Continue to Hold SET Press B Again TR-825 Menu Structure Audio Channel B OptionsTR-825 Menu Structure Special Key Sequences Lockout System Walk-Thru Blank Problem Solution TroubleshootingBlank Tech Tips Microphone Gain AdjustmentFrequency Interaction Blank Battery Life TR-800 Battery InformationTR-825 Blank Common Intercom Systems SpecificationsBlank Accessories and Replacement Parts Blank End-User License Agreement for Telex Software Software LicenseBlank FCC Licensing Certification InformationEU Declaration of Conformity PN 803257-1 Rev. H March Made in U.S.A