Telex BTR-800, TR-825 TR-800 Menu Structure Special Key Sequences Lockout, 1st Use Default

Page 56

TR-800 Menu Structure

Special Key Sequences

Lockout

•Press [UP]+[DOWN] for 3 seconds to lock or unlock the beltpack. The words “Loc on” will be displayed when the

feature is activated, “Loc oFF” will be displayed when the beltpack is unlocked. Pressing [MENU] will still function to view screens, but [SET] will no longer start any edit- ing. ClearScan™, First use, Factory default and Feature enable/disable are no longer accessible.

1st Use Default

•Press [MENU] while turning on the beltpack to enter the 1st use default setup screen. This places the unit on group

01A with channel 01 flashing. Any user-programmed frequencies that had been entered previously are re- tained. The beltpacks must now be set to different trans- mit channels using the [UP]/[DOWN] buttons. Then [SET] is hit to place the units on those channels. If lock- out had been activated, the beltpack comes up where it was last left regardless of [MENU] being pressed on power-up.

Factory Default

•Pressing all four buttons [MENU]+[SET]+[UP]+[DOWN] at the same time for three seconds places the unit on group 01A with channel 01 flashing, just like beltpack 1st

use default, except the all user-programmed frequencies that had been entered previously are erased. After the buttons are released, it still may take several seconds for the beltpack to reset. The beltpacks must now be set to different transmit channels using the [UP]/[DOWN] but- tons. Then [SET] is hit to place the units on those chan- nels. If lockout had been activated, the beltpack comes up where it was last left regardless of these four keys being pressed.

7-21

Image 56

Contents JTN Telex Thank you for choosing RadioComTM Table of Contents Tech Tips General Description System FeaturesIntroduction BTR-800 Block Diagram WTA aLocal Headset Wiring BTR-800 Base StationControls and Connections Front Panel BTR-800 Front PanelControls and Connections Rear Panel BTR-800 Rear PanelBTR-800 Specifications OverallBlank TR-800 Top Panel TR-800 BeltpackControls and Connections Top Panel TR-800 Rear Panel/Connector/Antennas Push-to-Talk/Push-to-Transmit SwitchHeadset Jack Wiring LCD Liquid Crystal DisplayTR-800 Specifications Blank TR-825 Beltpack Telex RAAudio + Audio a Switched Headphone Ground TR-825 Rear Panel/Connector/AntennasTR-825 Specifications Blank Initial Equipment Set-Up UnpackingBTR-800 TR-800, TR-825Antenna Placement Antenna ConnectionAntenna Polarization Distance between AntennasKeeping Site Clear to Antenna Distance Between base station and beltpackOperating System Near Obstructions Antenna Placement Improving Reception and Increasing RangePower Connection Transmit SwitchesBase Station Set-up LocationInternal Transmit Switches Intercom SwitchInternal Transmit Switches RJ-11 Type/ Four-wire PinoutRTS Distribution Panel TW5W Example Interface to an RTS TW SystemAudio Board Part Number and Dual Listen Component Locations Parts to be Removed by User to Enable Dual ListenDual Listen Functionality Auxiliary Input/Output Internal Auxiliary Input Routing SwitchAuxiliary Input Routing Switch Relay Output Schematic Stage Announce / Relay ContactsRelay Contact Jack Adapter Screw Terminal Adapter Internal Stage Announce Level ControlBase Station Link Cable Base Station LinkTwo Stand Alone Base Stations Connected Together Beltpack Set-up Battery Installation Charger and battery pack damageBattery Installation May resultTransmit mode Headset ConnectionTR-800 and TR-825 Rear Panel Push-to-Talk PT Talk Recommended positionBlank Pre-Walk-Thru Checklist Blank System Operation Frequency Plan OverviewSystem Quick Start Factory-Defined GroupsPower Base Station OperationLocal Headset Intercom a and BDisplay Contrast LCD ContrastBTR-800 Menu Structure Main Screen Flowchart Beltpack Activity Code Definitions Power-Up ScreenOperating Screen SET Last Rx Changed Group / Channel SelectUP / Down Group / Frequency Select Frequency Edit User-Programmed Groups OnlyClearScanTM ClearScan1st Use Default Factory DefaultSpecial Key Sequences Lockout CopyBeltpack Operation TR-800 and TR-825 Top and Rear PanelBeltpack Feature Enable/Disable Menus TR-800 Menu Structure Beltpack Menu StructureTR-800 Menu Structure Power-Up Screens Power-Up ScreensTR-800 Menu Structure Group / Channel Screen Group / Channel ScreenTR-800 Menu Structure Transmit Screen Transmit ScreenTR-800 Menu Structure Receive 1 Screen Receive 1 ScreenTR-800 Menu Structure Receive 2 Screen Receive 2 ScreenTR-800 Menu Structure ClearScan ClearScanTR-800 Menu Structure Stage Announce Enable/Disable Wireless Talk Around Enable/DisableTR-800 Menu Structure Audio Channel a or B Disable/Enable Talk Button Latch on/Latch offTR-800 Menu Structure Special Key Sequences Lockout 04A Scn TR-825 Menu Structure Beltpack Menu StructureTR-825 Menu Structure Power-Up Screens TR-825 Menu Structure Group / Channel Screen 704.700 TR-825 Menu Structure Transmit ScreenTR-825 Menu Structure Receive 1 Screen TR-825 Menu Structure Receive 2 Screen Ab SEP TR-825 Menu Structure Audio Output04b TR-825 Menu Structure ClearScanTMTR-825 Menu Structure Stage Announce Enable/Disable SA onTR-825 Menu Structure Wireless Talk Around TA bTR-825 Menu Structure Audio Channel a Options Audio Channel a OptionsTR-825 Menu Structure Audio Channel B Options Hold SET and Press B Continue to Hold SET Press B AgainTR-825 Menu Structure Special Key Sequences Lockout System Walk-Thru Blank Troubleshooting Problem SolutionBlank Frequency Interaction Microphone Gain AdjustmentTech Tips Blank TR-825 Battery InformationBattery Life TR-800 Blank Intercom Systems Specifications CommonBlank Accessories and Replacement Parts Blank Software License End-User License Agreement for Telex SoftwareBlank Certification Information FCC LicensingEU Declaration of Conformity PN 803257-1 Rev. H March Made in U.S.A