Datalogic Scanning Industrial PDA manual Installing the Battery Pack

Page 9

Powering the Pegaso

Lithium-ion battery packs may get hot, explode, ignite, or/and cause serious injury if exposed to abusive conditions.

Do not place the battery in or near fire, direct sunlight, or other

high temperature locations, or heat the battery.

Do not connect the positive terminal and negative terminal of the

WARNING

battery to each other or short circuit battery terminals with any

 

 

metal object (such as wire, coin or metallic object).

Do not expose the battery to liquids, or allow to get wet.

Do not disassemble, modify, open, crush, bend, deform, puncture, shred, remanufacture or pierce the battery. The battery contains safety and protection devices, which, if damaged, may cause the battery to generate heat, explode or ignite.

Use only battery packs that have been authorized by Datalogic per IEEE Standard 1725-200x for GSM/GPRS/EDGE operation.

Promptly dispose of used batteries in accordance with local regu- lations.

Battery usage by children should be supervised.

Avoid dropping the PDA or battery. If the PDA or battery is dropped, especially on a hard surface, and the user suspects dam- age, return it to a service center for inspection.

Only use the battery for the system for which it is specified.

In the event the battery leaks and the fluid gets into your eye, do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid could cause damage to the eye.

Datalogic recommends annual replacement of rechargeable battery packs to ensure maximum performance.

Installing the Battery Pack

When you first remove the Pegaso from the box, you must charge both the battery pack and the backup battery for a minimum of 4 hours.

The Pegaso’s Battery and its cover are integrated — they do not come apart.

Complete the following instructions to install the battery pack:

1.Loosen the elastic handstrap by releasing it from the bottom of the unit (refer to the PRG).

2.Orient the battery pack with the latch facing toward the top of the Pegaso (refer to Figure 2 on page 8).

3.Replace the battery door by inserting the bottom tab into the unit, then clicking the latch into place. If the battery pack is installed incorrectly, it will not seat properly.

Quick Reference Guide

7

Image 9
Contents Industrial PDA Disclaimer Table of Contents Industry Canada statement Appendix a Microsoft Windows CEOverview FeaturesTriggers Powering the Pegaso Battery PackGetting Started Powering the Pegaso Do not expose the battery to liquids, or allow to get wet Installing the Battery PackBattery Power System Tray Battery Status IndicatorsSystem Tray Battery Status Indicators Battery Icon Description Status Charging Charging the Batteries Battery Charging Methods and IndicationsCharging with the Dock Pull Upward to Remove USB/Serial ConnectorSetting Up the Mobile Computer Charging with a Battery ChargerBackup Battery Connecting to a PC IP Network Setup Bluetooth SetupTouchscreen Calibration Getting ConnectedModifying Network Connection Settings RF Setup Summit Client UtilityUsing the Stylus Setting the Date and TimeNavigating the Display Command BarAmbient Light Sensor Screen ProtectorApplication Navigation Task BarTranscriber Soft Keypad/Input PanelInput States and their System Tray Indicators System Tray Keyboard IndicatorsKeypad Keypad Overview Special KeysKey Keypad Key Keypad Alpha Characters and SymbolsKey Keymap Laser Scanning Scanning Bar CodesPersistent Memory Persistent MemoryResetting the Pegaso Warm ResetContext Sensitive Help After Warm Reset Cold ResetSafe Reset After Cold ResetProcedure to Safe Reset Maintaining the Pegaso After Safe ResetTroubleshooting Problems, Causes, and Solutions TroubleshootingNot accept scan Flashing RED Start RF Connectivity TroubleshootingResources Technical SupportDatalogic Mobile Website Support Reseller Technical Support Telephone Technical SupportInstall Avalanche SE Installation RequirementsQuick Start RAM Access the Avalanche SE Console Additional Console Information Connect To Your Mobile DevicesManage Mobile Devices Additional Functionality Configure Network and Wireless SettingsInstall Additional Software Packages Connect to Devices Using Remote Control Quick Reference Guide Additional Resources Definitions Transfers, Support Infringement Government Restricted Rights International Use Quick Reference Guide Appendix a Microsoft Windows CE End User License Agreement Quick Reference Guide Datalogic Mobile Pegaso Windows CE Product Warranty Assignment Laser Safety Label Laser Safety LabelRegulatory Statements Advisory StatementRadiation Exposure Statement Industry Canada statementPegaso Industrial PDA with Windows CE French EnglishItalian GermanDanish DutchSwedish Norwegian FinnishSpanish PortugueseChinese Japanese Europe EU Declaration of Conformity 0560 Declaration of Conformity Page Datalogic Mobile, Inc