Pentair PS6, P4, PS8, PS4, and P8 Power Center PCB DIP Switch Settings, DIP Switch Functions

Page 28

Page 28

Section 7. Power Center PCB DIP

Switch Settings

IMPORTANT Do not program equipment ON/OFF times until all DIP switches are set.

7.1DIP Switch Functions

DIP #1 ON- AUX 1 Controls Pool Cleaner

If you installed a booster pump for a pool cleaner, the relay coil for the booster pump must be plugged into the AUX 1 relay socket. If a non-booster pump cleaner is installed, plug the JVA into the cleaner JVA socket. Turn ON DIP Switch #1.

•Main filter pump turns on whenever cleaner turns on.

•Cleaner will not turn on until filter pump has been on for three (3) minutes (to ensure priming of system).

•Cleaner turns off when water circulation is to spa.

•Cleaner turns off when spa spillover feature is activated.

•Cleaner turns off for three (3) minutes when solar is activated (to ensure air is purged from the system).

•AquaLink RS PDA Handheld Remote display reads "CLEANER" rather than "AUX 1".

DIP #2 ON- AUX 2 Controls Low Speed of Filter Pump

Turn this switch ON if you want to control both speeds of a two-speed filter pump. With this switch on, the filter pump button on the AquaLink RS PDA will control high speed and the HOT KEY 2 (default) button will control low speed.

IMPORTANT You must also install a Jandy Two- Speed Relay.

DIP #3 ON- AUX 3 Controls Spa Spillover (Operates with Pool/Spa Combination)

Turn this switch ON, and when the AUX 3 button on the AquaLink RS PDA (or Spa Side Switch) is pressed, the Return Valve Actuator will rotate to spa circulation. Because the Intake Valve Actuator does not rotate, the spa will fill with water and overflow into the pool.

NOTE Leave AUX 3 relay socket empty.

DIP #4 ON- Heater Cool Down Disabled

Turn this switch ON to disable the heater cool down safety feature on the AquaLink RS.

CAUTION

Turn this DIP Switch ON only if you are using an electric heater or a heat pump that does not retain residual heat. If you are turning this switch ON for service purposes, be sure to turn it back off.

DIP #5 ON- Factory Use Only

This switch is used for calibration by Jandy certified technicians only. Please leave this switch in the OFF position.

DIP #6 ON - Pool/Spa Combination Systems Only

Change Spare AUX to activate when Filter Pump is on and system is in spa mode. Spare AUX socket is on the back side of the Power Center PCB.

DIP #7 ON- Not Used

Dip #8 ON- Heat Pump Instead of Gas Heater

Turn this switch ON if you have installed a heat pump instead of a gas heater. After thermostat setting has been reached, heater will remain OFF for 5 minutes.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Installation Manual PDA Pool Digital Assistant Page Table of Contents Important Safety Instructions To Reduce the Risk of InjuryAvertissement Package Contents System OverviewSystem Component Specifications and Dimensions Power SupplyService Switch Contact Rating RelaysBasic Plumbing Plumbing for Pool and Spa Combination Booster Pump Pool Cleaner Plumbing Non-Booster Pump Pool Cleaner PlumbingInstallation Power Center MountingHigh Voltage Wiring System Power Neutral2 3HP Standard Relays Bonding the Power Center Standard Power Center BondingUnderwater Lighting Gfci Wiring Gfci Installation for Underwater LightingVolt Jandy Pool and Spa Light Wiring Diagram Low Voltage Wiring Bezel Connection PDA J-Box Cable Connection to Power Center PCBHeater Connection Guidelines for Sophisticated Diagnostic SettingTurn the heater switch to the on position For dual thermostat heaters turn switch toHeater and Heat Pump/Chiller Wiring Temperature Sensors PDA Transceiver J-box InstallationOutdoor Transceiver J-box Installation Jandy Valve ActuatorsPDA Handheld Remote Installation Changing the Frequency ChannelSystem Startup Set slide switch on J-Box PCB toHandheld Remote Programming Basic Programming Menu Set the Time Menu Set the Temperature MenuLabel Auxiliary Functions Menu Set Freeze Protection Menu Assign JVAs MenuPDA System Defaults and General Modes Power Center Service Switch Auto Mode automaticService Mode Timeout ModeBattery Backup PDA Handheld Remote Menu Flow Chart PDA Quick Troubleshooting Guide TroubleshootingSymptom Problem Possible Solution Symptom Problem Possible Solution Power Center Wiring Diagram JVA JVAPower Center PCB DIP Switch Settings DIP Switch FunctionsFactory setting is with all DIP Switches off DIP Switch Settings for Pool and Spa CombinationDIP Switch # DIP Switch Settings for Pool or Spa Only General, Water Feature and Light Aux Labels General Labels Light Labels Waterfall LabelsLimited Warranty

PS8, P4, PS6, PS4, and P8 specifications

Pentair, a global leader in water treatment and flow solutions, continues to innovate with its robust line of products designed for both residential and commercial applications. Among these, the P8, PS4, PS6, P4, and PS8 models exemplify Pentair's commitment to delivering efficiency, quality, and performance in water management.

The Pentair P8 is renowned for its high-capacity performance, offering substantial flow rates suitable for larger homes or commercial establishments. This system is equipped with advanced filtration technologies that remove contaminants while retaining essential minerals. Its compact design makes it easy to install in various settings, and it operates quietly, ensuring minimal disruption to daily activities.

Next in line is the PS4, a powerful solution designed for medium-sized applications. The PS4 features a multi-stage filtration system, which enhances water purity and taste. With energy-efficient components, it minimizes operational costs while ensuring top-tier performance. The unit is also designed for easy maintenance, allowing users to replace filters with minimal effort, thus prolonging the system's lifespan.

The PS6 model offers enhanced capabilities, integrating advanced monitoring technology that provides real-time data on water quality and system performance. This connectivity feature allows users to identify potential issues early and optimize their usage patterns. The PS6 is particularly suited for households with stricter water quality requirements, making it ideal for families or individuals highly conscious of their water purity.

The P4 model is specifically designed for smaller residential applications. Despite its compact size, the P4 does not compromise on effectiveness. It utilizes innovative filtration materials that deliver excellent contaminant removal rates, making it a reliable choice for personal and environmental health. Its user-friendly interface and low maintenance requirements make it a favorite among homeowners.

Lastly, the PS8 represents the pinnacle of Pentair's technology, designed for larger-scale commercial use. It boasts an impressive filtration capacity paired with advanced water quality monitoring and control systems. The PS8 effectively manages higher volumes of water, ensuring consistent output quality under varying conditions. Its durable construction and high efficiency provide significant cost savings over time, making it a wise investment for enterprises.

In summary, Pentair continues to lead the industry with its diverse range of water treatment solutions. The P8, PS4, PS6, P4, and PS8 models offer distinct features tailored to meet varying needs, while their proprietary technologies ensure that consumers receive safe and clean water efficiently, paving the way for healthier communities.
Top Page Image Contents