Pentair PS4, P4, PS8, PS6, and P8 installation manual Limited Warranty

Page 32

H0572200B

LIMITED WARRANTY

Thank you for purchasing Jandy® pool and spa products. Jandy Pool Products, Inc. warrants all parts to be free from manufacturing defects in materials and workmanship for a period of one year from the date of retail purchase, with the following exceptions:

AquaLink® RS units installed with Jandy® Surge Protection Kits will be covered for two years.

NeverLube® valves are warranted for the life of pool and/or spa on which they were originally installed.

AquaPureTM Electronic Chlorine Generator Electrolytic Cells carry a 5 year limited warranty on a prorated basis.

This warranty is limited to the first retail purchaser, is not transferable, and does not apply to products that have been moved from their original installation sites. The liability of Jandy Pool Products, Inc. shall not exceed the repair or replacement of defective parts and does not include any costs for labor to remove and reinstall the defective part, transportation to or from the factory, and any other materials required to make the repair. This warranty does not cover failures or malfunctions resulting from the following:

1.Failure to properly install, operate or maintain the product(s) in accordance with our published Installation, Operation and Maintenance Manuals provided with the product(s).

2.The workmanship of any installer of the product(s).

3.Not maintaining a proper chemical balance in your pool and/or spa [pH level between 7.2 and 7.8, Total Alkalinity (TA) between 80 to 120 ppm, Total Dissolved Solids (TDS) less than 2000 not including salt ppm].

4.Abuse, alteration, accident, fire, flood, lightning, rodents, insects, negligence or acts of God.

5.Scaling, freezing, or other conditions causing inadequate water circulation.

6.Operating the product(s) at water flow rates outside the published minimum and maximum specifications.

7.Use of non-factory authorized parts or accessories in conjunction with the product(s).

8.Chemical contamination of combustion air or improper use of sanitizing chemicals, such as introducing sanitizing chemicals upstream of the heater and cleaner hose or through the skimmer.

9.Overheating; incorrect wire runs; improper electrical supply; collateral damage caused by failure of O-Rings, DE grids, or cartridge elements; or damage caused by running the pump with insufficient quantities of water.

LIMITATION OF LIABILITY:

This is the only warranty given by Jandy Pool Products, Inc. No one is authorized to make any other warranties on behalf of Jandy Pool Products, Inc. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. JANDY POOL PRODUCTS, INC. EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, INDIRECT OR PUNITIVE DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY. This warranty gives you specific legal rights. You may also have other rights which vary by state or province.

WARRANTY CLAIMS:

For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number and date of installation. The installer will contact the factory for instructions regarding the claim and to determine the location of the nearest designated service center. If the dealer is not available, you can locate a service center in your area by visiting www.jandy.com or by calling our technical support department at (707) 776-8200 extension 260. All returned parts must have a Returned Material Authorization number to be evaluated under the terms of this warranty.

ETL LISTED

 

PDA HANDHELD REMOTE

CONFORMS TO

FCC ID: S8F826X

UL STD 1563

 

CERTIFIED TO

PDA TRANSCEIVER

FCC ID: S8F8252

CAN/CSA C22.2 NO. 218.1

 

Jandy Pool Products, Inc.

6000 Condor Drive • Moorpark, CA USA 93021 • 707.776.8200 • Fax 707.763.7785

Litho in U.S.A. © Jandy Pool Products, Inc. 0610

Image 32 Contents
Installation Manual PDA Pool Digital Assistant Page Table of Contents Important Safety Instructions To Reduce the Risk of InjuryAvertissement Package Contents System OverviewSystem Component Specifications and Dimensions Power SupplyService Switch Contact Rating RelaysBasic Plumbing Plumbing for Pool and Spa Combination Booster Pump Pool Cleaner Plumbing Non-Booster Pump Pool Cleaner PlumbingInstallation Power Center MountingHigh Voltage Wiring System Power Neutral2 3HP Standard Relays Bonding the Power Center Standard Power Center BondingUnderwater Lighting Gfci Wiring Gfci Installation for Underwater LightingVolt Jandy Pool and Spa Light Wiring Diagram Low Voltage Wiring Bezel Connection PDA J-Box Cable Connection to Power Center PCBHeater Connection Guidelines for Sophisticated Diagnostic SettingTurn the heater switch to the on position For dual thermostat heaters turn switch toHeater and Heat Pump/Chiller Wiring Temperature Sensors PDA Transceiver J-box InstallationOutdoor Transceiver J-box Installation Jandy Valve ActuatorsPDA Handheld Remote Installation Changing the Frequency ChannelHandheld Remote Programming Basic Programming Menu Set slide switch on J-Box PCB toSystem Startup Label Auxiliary Functions Menu Set the Temperature MenuSet the Time Menu Set Freeze Protection Menu Assign JVAs MenuPDA System Defaults and General Modes Power Center Service Switch Auto Mode automaticService Mode Timeout ModeBattery Backup PDA Handheld Remote Menu Flow Chart Symptom Problem Possible Solution TroubleshootingPDA Quick Troubleshooting Guide Symptom Problem Possible Solution Power Center Wiring Diagram JVA JVA Power Center PCB DIP Switch Settings DIP Switch FunctionsDIP Switch # DIP Switch Settings for Pool and Spa CombinationFactory setting is with all DIP Switches off DIP Switch Settings for Pool or Spa Only General, Water Feature and Light Aux Labels General Labels Light Labels Waterfall LabelsLimited Warranty