Panasonic KX-TCD410NL Battery Charge, Battery Life, Fully charged, Display icon

Page 11

TCD410NL_E.book Page 5 Thursday, March 20, 2003 5:55 PM

Setting up

Battery Charge

At the time of shipment, the batteries are not charged. To charge, place the handset on the base unit. Please charge the batteries for about 7 hours before initial use. During charging, the battery icon is as shown below.

Fully charged

During charging

(Flashing)

 

Display icon

Battery strength

 

High

 

Medium

 

Low

 

Needs to be

 

charged

The handset which power is off will be turned on automatically when it is placed on the base unit.

In normal use, the handset and the base unit should be powered on at all times.

Battery Life

Battery life is dependent on use and conditions but in general when using fully charged Ni-MH batteries (700 mAh): Talk time: 10hrs approx.

Standby time: 120hrs approx.

When using Ni-Cd batteries (250 mAh): Talk time: 4hrs approx.

Standby time: 40hrs approx. (Times indicated are for peak performance)

The batteries reach peak performance after several full charge/discharge cycles. The batteries cannot be overcharged unless they are repeatedly removed and replaced.

If battery life is shortened then please check that battery and charge terminals are clean.

For maximum battery life, it is recommended that the handset is not

recharged until battery icon flashes .

Preparation

5

Page 10 Page 12
Image 11
Page 10 Page 12
Contents
Connection Setting UpBattery Installation Model No. KX-TCD410NLHandset Display Location of ControlsHandset Base UnitExample Your Guide to the DisplayCharacter Table 1st Menu 2nd Menu 3rd Menu Set-up Menu for HandsetFunction Action OperationsSymbols Used in This Operating Instructions Model No. KX-TCD410NL ContentsBefore Initial Use Accessories includedImportant Information Hook Display icon Battery ChargeBattery Life Fully chargedPlease use only Panasonic P03PNi-MH or P03HNi-Cd batteries Selecting the Battery TypeReplacing the Batteries Base unit Location of ControlsHandset Wall Mounting Making a Call Using the TelephonePower On/Off Setting the Clock/DateClearing One/All Dialled Items in the Redial List Making CallsRedialling Editing the Dialled Number in the Redial ListCaller ID Display Caller ID ServiceCaller ID Editing the Received Number in the Caller List Caller ID ListCalling Back Temporary Bell Off Receiver VolumeAnswering Calls Auto TalkName PhonebookStoring a Caller Information Phone NumberDialling with the Phonebook Editing a Caller InformationNumber Clearing a Caller InformationSave TEL NO.*2 Phone Number *1 NameClearing the Hot Key Registration Hot KeyRegistering a Phone Number as a Hot Key Dialling with Hot KeyBefore programming, please follow steps 1 to Handset SettingsTime Alarm Setting Time Alarm On/OffRinger Option Setting the Ringer VolumeDisplay Option Selecting the Standby Mode DisplayTone Option Digit Selecting the Talk Mode DisplayCall Option Call BAR On/OffOther Options Setting the Direct Call NumberSetting the Direct Call On/Off Key Lock Recall FeatureDialling Pause for PBX line/long distance service users Digit Base Handset Number Unit PIN*1 Base Unit SettingsPause Timing Cancelling Call Restricted Number 4-digit Base Unit PIN *1Select Flash Timing 4 Base Unit 5 2 6 1 PIN *1Storing the Area Codes/Country Code Automatic Route SelectionStoring the Carrier Codes Automatic Route Selection On/Off Digit Base Unit International Carrier ServicesTo Turn the International Code 00 Delete Mode ON/OFF Digit Base UnitHandset Initial Settings Function Initial SettingsReset Handset Digit Base Unit PIN*1 Reset Base Unit SettingsBase Unit Initial Settings Function Handset Registration to a Base Unit Multi-unit User OperationDigit Handset PIN *1 Cancelling a Base UnitCancelling a Handset Number of Rings *3 Ringer Mode Selection Setting the All Handsets ModeSetting the Selected Handsets Mode Handset Numbers *2 Setting the Selected then All Handsets ModeBase Unit Selection Transferring a Call to Another Handset/Conference Call IntercomIntercom between Handsets Before Requesting Help Problem Possible cause SolutionTCD410NLE.book Page 36 Thursday, March 20, 2003 555 PM Connections SpecificationsTechnical Information Garantiebewijs PIN IndexPQQX13533ZA D0403RY0 For your future referenceCustomer Care Helpline Tel. No VerkoopafdelingPQQW13138ZA D0603-0 Original Revision
Related manuals
Manual 47 pages 4.46 Kb