Panasonic KX-T2375ALW operating instructions Battery Replacement, Battery Precautions

Page 29

Battery Replacement

If “ ” ﬂashes, the battery power is low. Install new batteries. Replace the batteries within 1 minute to keep the programmed settings. But the programmed time setting will be cleared.

-	+			1	Disconnect the telephone line cord
	+				from the unit.
+		-
-+
2
2				2
					Press down in the direction of the
					arrow and remove the cover.
			1	3	Replace the batteries with new ones
				3	using correct polarity (i, j), and

close the cover.

4 Connect the telephone line cord to the unit.

³If the time is shown as “12-00” and “ ” ﬂashes after replacing the batteries, readjust the time.

Battery Precautions:

The batteries should be used correctly, otherwise the unit may be damaged by battery leakage.

—Do not mix different types of batteries.

—Do not charge, short-circuit, disassemble, heat or dispose of in ﬁre.

—Remove all the batteries when replacing.

Note:

—If you do not install the batteries or if the battery power is low, the time will be shown as “12-00” and “ ” will ﬂash. Readjust the time.

—Replace all the batteries every six months if using Alkaline batteries, or error may occur. (When you use Manganese batteries, replace all of them every three months.)

—Do not use nickel-cadmium batteries.

Useful Information

29

Image 29

Contents Model No. KX-T2375ALW Before Initial Use Accessories includedFor your future reference Serial No Date of purchaseContents Location of Controls VolumeDIAL\LOCK Button p Headset Jack p Display p Ringer Selector pDisplay Installing the Batteries SettingsAfter connection, lift the handset to check for a dial tone Connecting the Handset/Telephone Line CordConnecting a Communication Device Programming Summary of Preparations Press Program to store the settingMake sure that a call is not put on hold Press MuteYou can select AM/PM or 24-hour clock by programming Time AdjustmentSelecting the Ringer Volume Setting the LCD ContrastPress Press 1 toLocks, so the tab holds the handset Wall MountingWall Template Using the speakerphone Press SP-PHONE/HEADSETÛ Using the speakerphoneMaking Calls To redial the last number dialledTo put a call on hold To increase, press Volume . To decrease, press VolumeTo release the hold Press HoldTalk into the MIC microphone Answering CallsStoring Phone Numbers in Memory Speed DiallerEnter a phone number, up to 22 digits Press a memory station number 0 toTo erase a stored number Dialling a Stored NumberPress one of the one-touch auto dial buttons One-Touch DiallerTo store in an Upper memory location Memory location, press the one-touch To store in a Lower memory locationIf the phone number is in an Upper From a Lower memory location From an Upper memory locationMemory card Lift the handset or press SP-PHONE/HEADSETHow to Use the Pause Button Special FeaturesFor Analog PBX Line/Long Distance Service Users Muting Your ConversationTo turn OFF, press To turn ON, press Turning Music Played During the HoldPress a dialling button 1 to Recall ButtonSelecting the recall time Enter a new PIN code using a 4-digit Setting the PIN CodePress Mute Enter the current PIN code. Ex is entered NumberDial Lock To cancel the dial lockTo set the dial lock Enter the PIN code pEnter the PIN code p . Ex. Your PIN code is Call RestrictionTo set the call restriction Connecting the Optional Headset to the Unit Using the Optional HeadsetTo cancel the call restriction To adjust the headset receiver volume 4 levels Make sure to install the batteriesWhile using the headset, press Volume or Making/Answering CallsBattery Precautions Battery ReplacementBefore Requesting Help ProblemRemedyProblem Remedy Installations Environment Safety InstructionsUseful Information Instructions to customer Important InformationService difficulties PQQX13367ZA-BM F0102-0D