Linear AE-500 manual Programming Over the Telephone, Programming from the Local Keypad

Page 6

Programming Over the Telephone

The system can be programmed using a TouchTone™ telephone. The telephone’s keypad will act similar to the AE-500’s local keypad.

Connecting with a Telephone

1.Place a call to the telephone number of the line that AE-500 is connected to.

2.The AE-500 will answer and sound a tone for about ½ second.

3.After the tone, enter the master password, then press # (factory setting is 123456, your installer may have set a new password). If the password is correct, the system will sound two short beeps.

For multi-unit installations, enter the unit number then # before entering the password.

4.Programming commands can now be entered from the telephone’s keypad. Refer to the following sections of this manual for programming step details.

When programming over the telephone, each programming step consists of entering programming data using the keypad. The system will sound beeps over the telephone to indicate correct or incorrect entries.

After a correct entry, two short beeps will sound.

After an incorrect entry, a long beep will sound.

After the complete programming step has been entered correctly, three short beeps will sound.

Re-entering a Command After a Mistake

If an incorrect entry, or an incorrect key is pressed during programming,

press and start the programming step over again.

Exiting Programming Mode

1. Press:

NOTE: The AE-500 will automatically exit Programming Mode after fi ve minutes of programming inactivity.

1. CALL THE SYSTEM

2. WAIT FOR THE TONE TO FINISH

3. ENTER THE MASTER PASSWORD THEN PRESS #

(TWO BEEPS SOUND WITH THE CORRECT PASSWORD)

NOTE: FOR MULTI-UNIT INSTALLATIONS, ENTER THE UNIT NUMBER THEN # BEFORE ENTERING THE PASSWORD THEN #

WHEN ENTERING COMMANDS:

CORRECT ENTRY = TWO SHORT BEEPS

INCORRECT ENTRY = ONE LONG BEEP

AFTER A COMPLETE STEP = THREE SHORT BEEPS

Programming from the Local Keypad

The system can be programmed using the local keypad on the faceplate of the AE-500. The display will show the programming information.

NOTE: When entering text, programming the AE-500 from a computer is the preferred method.

Accessing Programming from the Local Keypad

1.

Press & keys at the same time, then release.

2.

The display will show [PASSWORD:].

LOCAL KEYPAD ALPHANUMERIC ENTRY

(FOR PROGRAMMING STEPS REQUIRING TEXT)

NOTE: FOR EASY TEXT ENTRY

a b c d e f g h i

 

PROGRAM THE SYSTEM USING

 

A COMPUTER

 

3. Enter the master password (factory setting is 123456, your installer may have set a new password).

4.Press:

5.If the password is correct, the display will show [ENTER FUNCTION:].

6.Programming commands can now be entered on the local keypad. Refer to the following sections of this manual for programming step details.

m n o

j k l

v w x

s t u

• 1ST PRESS IS 1ST LETTER

• 2ND PRESS IS 2ND LETTER

• 3RD PRESS IS 3RD LETTER

• 4TH PRESS IS THE KEY NUMBER

• 5TH PRESS IS 1ST LETTER AGAIN

p q r

y z ,

Re-entering a Command After a Mistake

If an incorrect entry, or an incorrect key is pressed during programming,

to clear the keypad press and start the programming step over again.

Exiting Programming Mode

1. Press:

NOTE: The AE-500 will automatically exit Programming Mode after fi ve minutes of programming inactivity.

space, minus sign, dot

WAIT 3 SECONDS FOR THE NEXT CHARACTER (A BEEP WILL SOUND AFTER THE 3 SECOND DELAY TIME) OR PRESS ANOTHER KEY

THE FIRST LETTER OF EACH WORD WILL BE UPPER CASE,

TO MAKE AN ENTIRE WORD UPPER CASE TEXT, ENTER # FIRST

FINISH ENTRY BY ENTERING #

PRESS STAR KEY TO BACKSPACE, PRESS STAR AGAIN TO ERASE LINE

6

Image 6
Contents AE-500 Operation ContentsIntroduction Database OverviewSystem Features Programming with a Computer 71#UNIT# Setting up Multiple UnitsPress Enter the unit number Exit Programming Mode Le and click Upload to send the fi le to the unitProgramming Over the Telephone Programming from the Local KeypadData Restore Factory SettingsData Backup Programming Reference22#DIR#NAME#PHONE# 02#LENGTH#21#DIR#NAME#PHONE# 23#DIR#DIR#03#LENGTH# 33#CODE#CODE#Entry Code Programming 45#FC#ID# Wireless Transmitter Programming41#NUMBER#FC#ID# 43#FC#ID#Activate a Transmitter 42#FC#ID#47#FC#ID# Delete single Enrolled Transmitter57#LINE 1#LINE 2# 51#COUNT#58#KEY#ACTION# 62#CHIRP#63#TONE# 64#TIME#65#POS# 94#000000#000000# System UtilitiesRequesting Access with a Visitor Call Requesting Access with an Entry CodeRequesting Access with a Wireless Transmitter Resident can use their telephone’s keypad to grant accessTroubleshooting
Related manuals
Manual 1 pages 48.42 Kb