Linear AE-500 manual 03#LENGTH#, 33#CODE#CODE#, Entry Code Programming

Page 9

Entry Code Programming

An entry code is a number entered at the AE-500 keypad or remote keypad to request access. Up to 500 entry codes can be set. Entry codes can be from two to six digits in length (all will be the same length).

Entry codes can be programmed for timed or toggle operation. Timed relays activate for a programmed length of time. Toggle relays latch on until the next time a toggle entry code is entered, then the relay unlatches. Each entry code can also be set for a limited or unlimited number of uses.

An entry code will activate Relay Channel “A” or “B” depending on how the entry code is programmed and whether or not a remote keypad is attached:

When an entry code is programmed to activate a specifi c relay, the selected relay will activate when the code is entered on either the AE-500 keypad or the remote keypad.

When an entry code is programmed to activate both relays, and a remote keypad is attached, Relay Channel “A” will activate if the entry code is entered on the AE-500 keypad; Relay Channel “B” will activate if the entry code is entered on the remote keypad.

When an entry code is programmed to activate both relays, and a remote keypad is not attached, the entry code will activate both Relay Channels “A” and “B”.

When an entry code is programmed to activate both relays, only timed relay mode is available for that code, toggle relay mode is unavailable.

Changing the Entry Code Length

 

 

The factory setting for the entry code length is 4 digits. It can be set to 2-6 digits.

ENTRY CODE LENGTH

PPN 03

1.

If not already in Programming Mode, connect by telephone or use the local

03#LENGTH#

 

 

keypad. Enter the master password and access programming.

 

2.

Press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Enter the entry code length (2, 3, 4, 5, or 6).

 

 

4.

Press

 

 

 

 

 

LENGTH = NUMBER (2-6) OF ENTRY CODE DIGITS

 

 

 

 

 

 

 

 

 

 

5.

Exit Programming Mode if all programming is complete.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adding an Entry Code

 

 

 

 

1.

If not already in Programming Mode, connect by telephone or use the local

 

 

 

keypad. Enter the master password and access programming.

ADDING AN ENTRY CODE

PPN 31

2.

Press

 

 

 

 

 

 

31#CODE#CODE#RELAY#TEMP#

 

 

 

4.

Press

3.

Enter the entry code.

 

 

 

 

 

 

 

 

 

 

5.

Enter the entry code again.

CODE = THE NEW ENTRY CODE

 

6.

Press

 

 

 

 

 

 

 

 

 

 

 

 

RELAY = 1 FOR RELAY "A"

 

 

 

 

 

 

 

 

 

 

7.

If access to both relays is OK for this code, and the number of uses is

 

 

unlimited, skip to Step 12.

RELAY = 2 FOR RELAY "B"

 

8.

Enter the number for the relay output(s) that this entry code will be allowed

RELAY = 3 FOR RELAYS "A" AND "B"

 

 

to activate or for toggle operation:

RELAY = 4 TO TOGGLE RELAY "A" (ALTERNATES ON OR OFF)

Enter 1 for Relay “A” • Enter 2 for Relay “B” • Enter 3 for Relays “A” & “B”

RELAY = 5 TO TOGGLE RELAY "B" (ALTERNATES ON OR OFF)

Enter 4 to toggle Relay “A” • Enter 5 for to toggle Relay “B”

9.

Press

 

 

 

TEMP = NUMBER OF USES ALLOWED (1-250)

 

 

 

 

 

 

 

 

 

 

 

 

10.If the number of uses is unlimited, skip to Step 12.

11.Enter the number of uses allowed (1-250).

12.Press

13. Exit Programming Mode if all programming is complete.

Modifying an Entry Code

Once entry codes have been set, they can be modifi ed to change the relay(s) to activate or the number of uses permitted.

1.If not already in Programming Mode, connect by telephone or use the local keypad. Enter the master password and access programming.

2.Press

3. Enter the entry code.

4.Press

5.Enter the number for the relay output(s) that this entry code will be allowed to activate or for toggle operation:

Enter 1 for Relay “A” • Enter 2 for Relay “B” • Enter 3 for Relays “A” & “B”

Enter 4 to toggle Relay “A” • Enter 5 for to toggle Relay “B”

6.Press

7.If the number of uses is unlimited, skip to Step 9.

8.Enter the number of uses allowed (1-250).

9.Press

10.Exit Programming Mode if all programming is complete.

MODIFYING AN ENTRY CODE

PPN 32

32#CODE#RELAY#TEMP#

CODE = ENTRY CODE TO MODIFY RELAY = 1 FOR RELAY "A" RELAY = 2 FOR RELAY "B"

RELAY = 3 FOR RELAYS "A" AND "B"

RELAY = 4 TO TOGGLE RELAY "A" (ALTERNATES ON OR OFF) RELAY = 5 TO TOGGLE RELAY "B" (ALTERNATES ON OR OFF) TEMP = NUMBER OF USES ALLOWED (1-250)

Deleting an Entry Code

Entry codes can be deleted individually.

1.If not already in Programming Mode, connect by telephone or use the local keypad. Enter the master password and access programming.

2.Press

3. Enter the entry code to delete.

4.Press

5.Enter the entry code to delete again.

6.Press

7.Exit Programming Mode if all programming is complete.

DELETING AN ENTRY CODE

PPN 33

33#CODE#CODE#

CODE = THE ENTRY CODE TO DELETE

9

Image 9
Contents AE-500 Introduction ContentsOperation Database OverviewSystem Features Programming with a Computer Press Enter the unit number Exit Programming Mode Setting up Multiple Units71#UNIT# Le and click Upload to send the fi le to the unitProgramming from the Local Keypad Programming Over the TelephoneData Backup Factory SettingsData Restore Programming Reference21#DIR#NAME#PHONE# 02#LENGTH#22#DIR#NAME#PHONE# 23#DIR#DIR#03#LENGTH# 33#CODE#CODE#Entry Code Programming 41#NUMBER#FC#ID# Wireless Transmitter Programming45#FC#ID# 43#FC#ID#47#FC#ID# 42#FC#ID#Activate a Transmitter Delete single Enrolled Transmitter58#KEY#ACTION# 51#COUNT#57#LINE 1#LINE 2# 62#CHIRP#63#TONE# 64#TIME#65#POS# System Utilities 94#000000#000000#Requesting Access with a Wireless Transmitter Requesting Access with an Entry CodeRequesting Access with a Visitor Call Resident can use their telephone’s keypad to grant accessTroubleshooting
Related manuals
Manual 1 pages 48.42 Kb