Cobra Electronics CXR725C owner manual Privacy Code Scan, Or DCS can be scanned at a time

Page 12

Operation

Mode Functions

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

During channel scan (while receiving an incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that channel. Your radio will remain on that channel and return to Standby mode.

Privacy Code Scan

•

Your microTALK radio can automatically scan the Privacy

 

Codes (either CTCSS 01 through 38 or DCS 01 through 104)

 

within one channel. Only one set of privacy codes (CTCSS

 

or DCS) can be scanned at a time.

 

b. Press the Channel Up or Channel Down button to resume scanning channels.

If you press the Talk button while scanning, but more than

10 seconds after receiving a transmission, you will transmit on the channel on which you last received a transmission. This will return the radio to Standby mode.

If you do not press any button within 10 seconds after receiving a scanned transmission, your radio will automatically resume scanning channels.

SelectChannel

ModeButton

To scan privacy codes:

1.While in Standby mode, press the Channel Up or Channel Down button to choose the channel on which you wish to scan privacy codes.

2.Press the Mode button until either the CTCSS or the DCS icon appears on the display and the Scan icon and the privacy code numbers flash on the display.

During channel scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel or channel/privacy code that was displayed before you entered mode functions or the channel on which, during scanning, you last received a transmission. This will then return the radio to Standby mode.

b. Press the Mode button to proceed to set privacy

code scan on the channel that was either displayed before you entered mode functions or on which, during channel scanning, you last received a transmission (see page 19 for further details).

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the channel on which, during scanning, you last received a transmission.

ScanPrivacyCodes

ChannelButton

3.Press the Channel Up or Channel Down button to begin scanning privacy codes within the channel you selected.

The Scan icon will continue to be displayed when privacy code scan is on. Your radio will continue to scan privacy codes and stop as an incoming transmission is detected. Your radio will remain on that channel/privacy code for 10 seconds.

While setting privacy code scan, if you do not press any buttons for 15 seconds, your radio will automatically return to Standby mode on the channel/privacy code that was displayed before you entered mode functions.

18

Nothing Comes Close to a Cobra® 19

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Making Life Easier and Safer Product Features WarrantyFeatures Limited One-Year Warranty on Radios & ChargerRechargeable Battery Pack and Desktop Charger To install or replace battery packCaring for Your microTALK Radio Estimated operation time on full charge 10 hoursUsing Your Radio Selectable HighLow Power Output ChannelsOr Channel Down button Listening for a ResponseLock Feature Signal Strength MeterTo turn the lock feature on or off Auto Squelch/Maximum RangeMode Functions Scrolling through Mode FunctionsWill be displayed in the following order Privacy CodesSet Ctcss Privacy Codes To select a Ctcss privacy code Set DCS Privacy Codes To select a DCS privacy codeTo turn VOX mode on or off Voice Activated Transmit VOXMemory Locations To set VOX sensitivityChoose one of the following Press the Channel Up or Channel DownButton to select a memory location 0 through While recalling a stored memory locationTo de-program a memory location Channel ScanFlash on the display ThroughPress the Mode button to proceed to set privacy Privacy Code ScanOr DCS can be scanned at a time If you press the Talk button while scanning, but more thanMemory Location Scan Your microTALK radio can automatically scan up toProgrammed Memory Locations To scan memory locationsTo change call settings VibrAlert and Call AlertPress the Channel Up or Channel Down button to Call Tone Settings To change a call tone settingTo change keystroke tones Choose one of the followingGeneral Specifications FCC License For Products Used in Canada Industry Canada NoticeFor Products Used in the U.S.A FCC Licensing Required Product Service Safety and Trademark Safety Information for microTALK RadiosNormal Position Trademark Acknowledgement
Top Page Image Contents