Cobra Electronics LI 720 owner manual Or DCS can be scanned at a time, To scan privacy codes

Page 12

Operation

Mode Functions

Introduction

Operation

Customer Assistance Warranty

During channel scan (while receiving an incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that channel. Your radio will remain on that channel and return to Standby mode.

b. Press the Channel Up or Channel Down button to

Privacy Code Scan

•

Your microTALK® radio can automatically scan the Privacy

 

Codes (either CTCSS 01 through 38 or DCS 01 through 104)

 

within one channel. Only one set of privacy codes (CTCSS

 

or DCS) can be scanned at a time.

 

 

To scan privacy codes:

 

Select Channel

 

resume scanning channels.

If you press the Talk button while scanning, but more than

10 seconds after receiving a transmission, you will transmit on the channel on which you last received a transmission. This will return the radio to Standby mode.

If you do not press any button within 10 seconds after receiving a scanned transmission, your radio will automatically resume scanning channels.

During channel scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel or channel/privacy code that was displayed before you entered mode functions or the channel on which, during scanning, you last received a transmission. This will then return the radio to Standby mode.

b. Press the Mode button to proceed to set privacy

code scan on the channel that was either displayed before you entered mode functions or on which, during channel scanning, you last received a transmission (see page 19 for further details).

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the channel on which, during scanning, you last received a transmission.

Mode Button

Scan Privacy Codes

Channel Buttons

1.While in Standby mode, press the Channel Up or Channel Down button to choose the channel on which you wish to scan privacy codes.

2.Press the Mode button until either the CTCSS or the DCS icon appears on the display and the Scan icon and the privacy code numbers flash on the display.

3.Press the Channel Up or Channel Down button to begin scanning privacy codes within the channel you selected.

The Scan icon will continue to be displayed when privacy code scan is on. Your radio will continue to scan privacy codes and stop as an incoming transmission is detected. Your radio will remain on that channel/privacy code for 10 seconds.

While setting privacy code scan, if you do not press any buttons for 15 seconds, your radio will automatically return to Standby mode on the channel/privacy code that was displayed before you entered mode functions.

18

19

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Convenient and easy when using your microTALK Staying in touch with your family and friends isSecure your microTALK Radio while on the goProduct Features Warranty and Trademark AcknowledgementFeatures Trademark AcknowledgementAvoid exposure to extreme temperatures Replace battery compartment cover and belt clipCaring for Your microTALK Radio Estimated operation time on full charge 12 hoursUsing Your Radio Auto Battery SaveFor charging microTALK radios in desktop charger Turning on Your microTALK RadioTime-out Timer Available call tone settings To Illuminate DisplayTo switch from high to medium to low power Channels With the radio on, select anyLock Feature Signal Strength MeterBars visible, the weaker the signal MicroTALK Range To turn the lock feature on or offMode Functions Scrolling through Mode FunctionsSet Ctcss Privacy Codes To select a Ctcss privacy codeSet DCS Privacy Codes To select a DCS privacy codeSmall numbers flash on the display To listen to All Hazards Radio channelsTo turn VOX mode on or off To program a memory location Press the Mode button untilVoice Activated Transmit VOX Memory LocationsTo recall a stored memory channel location While recalling a stored memory locationTo de-program a memory location Channel ScanThrough To scan channelsPress the Mode button to proceed to set privacy Or DCS can be scanned at a timeTo scan privacy codes Your microTALK radio can automatically scan the PrivacyMemory Location Scan Your microTALK radio can automatically scan up toProgrammed Memory Locations To scan memory locationsTo change call settings VibrAlert and Call AlertChannel Down button to Call Tone Settings To change a call tone settingTo change keystroke tones Roger Beep Confirmation ToneGeneral Specifications FCC License General SpecificationsSafety Information for microTALK Radios Normal PositionProduct Service For Products Purchased in the U.S.A
Top Page Image Contents