Cobra Electronics LI 720 owner manual VibrAlert and Call Alert, To change call settings

Page 14

Operation

Mode Functions

Introduction

Operation

Customer Assistance Warranty

During memory location scan (while receiving an Incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that

VibrAlert® and Call Alert

•

Your microTALK® radio can alert you to incoming signals by

 

sounding an audible call tone, by vibrating silently or both.

 

memory location.

b. Your radio will remain on that memory location and return to Standby mode. Press the Channel Up or Channel Down button to resume scanning memory locations.

c. After 10 seconds of inactivity, unit starts scan again.

If you press the Talk button while scanning, but more than

10 seconds after receiving a transmission, you will transmit on the memory location on which, during scanning, you last received a transmission.

If you do not press any button within 10 seconds, your radio will automatically resume scanning memory locations.

During memory location scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel/privacy code that was displayed before you entered mode functions or memory location on which, during scanning, you last received a transmission.

b. Press the Mode button to proceed to other functions.

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the memory location on which, during scanning, you last received a transmission.

To reduce the number of memory locations being scanned, you may de-program any unwanted locations. (See page 16 to de-program a memory location.)

Mode Button

Channel Buttons

To change call settings:

VibrAlert® + Ring

1. Press the Mode button

 

until the Call Setting icon

 

flashes on the display.

 

The current setting (“01”

 

vibrate + ring, “02” vibrate

VibrAlert® Only

only or “03” ring only)

 

is displayed.

 

2. Press the Channel Up or

 

Channel Down button to

Ring Only

change the call setting.

 

3. Choose one of the following:

 

a. Press the Mode button

 

to enter the new setting

 

and proceed to other functions.

b. Press the Lock/Enter button to enter the new setting and return to Standby mode.

22

23

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Secure your microTALK Convenient and easy when using your microTALKStaying in touch with your family and friends is Radio while on the goFeatures Product FeaturesWarranty and Trademark Acknowledgement Trademark AcknowledgementCaring for Your microTALK Radio Avoid exposure to extreme temperaturesReplace battery compartment cover and belt clip Estimated operation time on full charge 12 hoursFor charging microTALK radios in desktop charger Using Your RadioAuto Battery Save Turning on Your microTALK RadioTo switch from high to medium to low power Time-out TimerAvailable call tone settings To Illuminate Display Channels With the radio on, select anyBars visible, the weaker the signal MicroTALK Range Lock FeatureSignal Strength Meter To turn the lock feature on or offSet Ctcss Privacy Codes Mode FunctionsScrolling through Mode Functions To select a Ctcss privacy codeSmall numbers flash on the display Set DCS Privacy CodesTo select a DCS privacy code To listen to All Hazards Radio channelsVoice Activated Transmit VOX To turn VOX mode on or offTo program a memory location Press the Mode button until Memory LocationsTo recall a stored memory channel location While recalling a stored memory locationThrough To de-program a memory locationChannel Scan To scan channelsTo scan privacy codes Press the Mode button to proceed to set privacyOr DCS can be scanned at a time Your microTALK radio can automatically scan the PrivacyProgrammed Memory Locations Memory Location ScanYour microTALK radio can automatically scan up to To scan memory locationsChannel Down button to To change call settingsVibrAlert and Call Alert To change keystroke tones Call Tone SettingsTo change a call tone setting Roger Beep Confirmation ToneSafety Information for microTALK Radios General Specifications FCC LicenseGeneral Specifications Normal PositionProduct Service For Products Purchased in the U.S.A
Top Page Image Contents