Cobra Electronics LI 720 Memory Location Scan, Your microTALK radio can automatically scan up to

Page 13

Operation

Mode Functions

Introduction

Operation

Customer Assistance Warranty

During privacy code scan (while receiving an incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that channel/privacy code. Your radio will remain on that channel/privacy code and return to Standby mode.

b. Press the Channel Up or Channel Down button to resume scanning privacy codes.

If you press the Talk button while scanning, but more than 10 seconds after receiving a transmission, you will transmit

Memory Location Scan

•

Your microTALK® radio can automatically scan up to

 

10 programmed Memory Locations.

 

If there are one or fewer memory locations programmed in your radio, the scan memory locations option will not be available. To program at least two (2) memory locations, see program memory locations on page 13.

on the channel/privacy code on which you last received a transmission. This will then return the radio to Standby mode.

If you do not press any button within 10 seconds, your radio will automatically resume scanning privacy codes.

During privacy code scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel/privacy code that was displayed before you entered mode functions or the channel/privacy code on which, during scanning, you last received a transmission. This will return the radio to Standby mode.

b. Press the Mode button to proceed to set memory location scan (see page 21 for further details).

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the channel/ privacy code on which, during scanning, you last received a transmission.

Mode Button

Scanning Locations

Channel Buttons

To scan memory locations:

1.Press the Mode button until the Scan icon, Memory icon and the memory location number flash on the display.

2.Press the Channel Up or Channel Down button to begin scanning memory locations.

The Scan icon and the Memory icon will continue to be displayed when memory location scan is on. Your radio will continue to scan memory locations and stop if an incoming transmission is detected. Your radio will remain on that memory location for 10 seconds.

While setting memory location scan, if you do not press any buttons for 15 seconds, your radio will automatically return to Standby mode on the channel/privacy code displayed before you entered mode functions.

20

21

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Staying in touch with your family and friends is Convenient and easy when using your microTALKSecure your microTALK Radio while on the goWarranty and Trademark Acknowledgement Product FeaturesFeatures Trademark AcknowledgementReplace battery compartment cover and belt clip Avoid exposure to extreme temperaturesCaring for Your microTALK Radio Estimated operation time on full charge 12 hoursAuto Battery Save Using Your RadioFor charging microTALK radios in desktop charger Turning on Your microTALK RadioAvailable call tone settings To Illuminate Display Time-out TimerTo switch from high to medium to low power Channels With the radio on, select anySignal Strength Meter Lock FeatureBars visible, the weaker the signal MicroTALK Range To turn the lock feature on or offScrolling through Mode Functions Mode FunctionsSet Ctcss Privacy Codes To select a Ctcss privacy codeTo select a DCS privacy code Set DCS Privacy CodesSmall numbers flash on the display To listen to All Hazards Radio channelsTo program a memory location Press the Mode button until To turn VOX mode on or offVoice Activated Transmit VOX Memory LocationsWhile recalling a stored memory location To recall a stored memory channel locationChannel Scan To de-program a memory locationThrough To scan channelsOr DCS can be scanned at a time Press the Mode button to proceed to set privacyTo scan privacy codes Your microTALK radio can automatically scan the PrivacyYour microTALK radio can automatically scan up to Memory Location ScanProgrammed Memory Locations To scan memory locationsVibrAlert and Call Alert To change call settingsChannel Down button to To change a call tone setting Call Tone SettingsTo change keystroke tones Roger Beep Confirmation ToneGeneral Specifications General Specifications FCC LicenseSafety Information for microTALK Radios Normal PositionFor Products Purchased in the U.S.A Product Service
Top Page Image Contents