Uniden WDECT 2355+2 quick start Remote Operation, Remote access away from home

Page 59

UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 53

REMOTE OPERATION

You can check, play, or delete messages, even record a new greeting message from a remote location (when you are away from home, or from another room using a handset). Additionally, you can turn On or Off your answering system remotely.

Remote access away from home

You can operate your answering system from a remote location using any touch-tone telephone.

1)Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about 15 rings and sounds a series of beeps.

2)During the greeting message (or a series of beeps when the answering system is off), press # and enter your PIN code within 2 seconds (see “Setting a PIN Code” on page 17 or 46).

3)The answering system announces the current time and the number of messages stored in memory. You hear “To play incoming messages, press pound-two. For help, press pound-zero.” You will hear a beep.

4)Enter a command within 15 seconds, each command there after must be entered within 2 seconds. You may select a command from the following chart:

Command	Function	Command	Function
# then 1	Repeat a Message*	# then 6	Answering System On
# then 2	Playing incoming Messages	# then 7	Memo Record/Stop**
# then 3	Skipping a Message	# then 8	Greeting Message Record/Stop**
# then 4	Deleting a Message	# then 9	Answer System Off
# then 5	Stop Operation	# then 0	Help Guidance

•The time stamp will not be heard until you have set the time. See “Setting the Time” on page 46.

•The system will only playback messages for four minutes and then it returns to the command waiting mode. To continue playing your messages, press # then 2 again within 15 seconds.

•If you enter an incorrect PIN code three times, you will hear a beep and the system will return to standby.

•During the remote operation, Lr appears on the base.

•If the answering system is recording an incoming message, the recording operation is canceled when you access

your answering system remotely.

•For your convenience a remote operation card is provided for you to use while away from home (refer to page 68).

[ 53 ]

Image 59

Contents Guide Choose Installation & SafetyHowever it does not attempt to explain any Installed and operating as quickly as possibleAdvanced features of the WDECT2355 series Quick Start GuideConnecting the charger Installing the battery packCharging the handsets Contents Controls and Functions Main Base Welcome Uniden Company PhilosophyFeatures Terminology Checking the Package ContentsMounting the Base Unit on a Wall Cleaning the battery charging contacts Battery MaintenanceBattery use time per charge Low battery alertTo remove the beltclip Installing the BeltclipBattery replacement and handling To attach the beltclipN d s e t Headset Installation OptionalDisplay and Icons N 1 2 0 0 aRoom Monitor About the Menu OptionsSummary of the Main Menu and Submenu Submenu name Description Handset SetupDefault is 9 time Answering SetupSystem Reset Global SetupEntering the Menu Setting UP the MenuDirectLink Mode Vol/ or /vol Using Room MonitorRoom Monitor To Room Monitor Handset #2 Base RoomMonitor Handset #2Selecting a Ringer Tone Handset SetupDistinctive Ringer Setup Setting the AutoTalkSetting the Key Touch Tone Answering System SetupSetting the Anykey Answer Setting the True BannerSetting the Call Screen Setting the Ring TimeSetting the Record Time Setting the Message Alert On or OffSetting Day and Time Global SetupSetting Name Tag POP ID Setting Insert Zero New Zealand onlyCopy Phonebook Setting the Dial Mode Australia onlyDe-register the Handset System ResetReplacing the Base Setting Redial/pause Making and Receiving CallsSpeaker To unlock the keypad Keypad LockPlacing a Call on Hold To lock the keypadDeleting a Redial Record Redialing from Standby ModeRedialing from Talk Mode Redialing a CallRinger Mute Handset ringer volumeEarpiece and speaker volume Redialing from the BaseWith the base Do not Disturb DNDMute Microphone With the handsetClarity Booster Tone Dialing SWITCH-OVER Australia onlyTraveling OUT-OF-RANGE Talk Privacy ModeWhen speaking on the handset WAY ConferencingNEW Message LED When speaking on the baseFind Handset Flash and Call WaitingPress phonebook PhonebookPhonebook Search A-Z Store Select Movies Beethoven9/SPD1 Distinctive Ring No Selectn FlickerSpeed Dial No Selectn SPD1Empty Steps for Entering Names and Special Characters If you make a mistake while entering a name If you recall the phonebook during a call Viewing the PhonebookSearch StoreSpeed Dialing Making Calls Using the PhonebookFrom Standby Mode From Talk ModeDeleting the Stored Data Editing the Stored DataMaking Calls with Memory Dialing Chain DialingMemory Dialing Base only Storing Phone Numbers0295979035 Caller ID21/12 1120AM Jane SmithTo finish the viewing operation, press or during a call Viewing the Caller ID ListCaller ID New Total Delete All? Yes Deleting Information from the Caller ID ListDeleting all Caller ID names/numbers Delete Caller ID YesStoring Caller ID messages in the Phonebook Using the Caller ID Message ListCalling a party from the Caller ID list Adding Zero to Caller ID message New Zealand onlyIntegrated Answering Device FeaturesTurning the Answering System ON/OFF Answering System Default SettingsFunctions Default Setting Reference Base Handset Setting UP Your Answering System For instructions Adjusting the speaker volume levelAnswering System Settings Press SET to select the hour Setting the TimeSetting a PIN code Press clock/MENUSelecting the message record time Setting the ring timePress skip/SELECT or repeat/SELECT to choose On or Announce only featureSetting the message alert Turning the message alert tone off by pressing any keyFrom the handset Setting the call screenScreening a call From the baseRepeat/SELECT Using Your Answering SystemPlaying your messages Repeating a messageDeleting a message Skipping a messageFrom the base Voice memoRecording a conversation From the handset# then Memo Record/Stop Skipping a Message Remote access away from homeRemote Operation Remote access with the handset Skipping a Message Remote Key FunctionRepeat a Message Answering System On Memo Record/StopMulti-Handset Expendability Expanding Your PhoneWhile the handset is registering Register the HandsetPlace handset on main base to register DirectLink Call To enter the DirectLink mode e SeeSUN 1200A Handset #1 DirectLink Mode To DirectLink Press Room MonitorTo intercom INTERCOM/CALL Transfer FeatureIntercom From handset to handset or to the baseTransfer/int’com or Call Transfer FeatureReplacing the Base Hold,to Transfer HandsetTo register all the handsets do the following steps Changing the Digital Security CodeSymptom Suggestion TroubleshootingMake sure that you have registered all handsets With another handsetsBrief message Make sure the call screen feature is set to onMessages are incomplete G, H IndexOne Year Limited Warranty WarrantyTurn on the answering system remotely Remote access away from homeRemote Operation Card Task Key Memo Expand Your System