Roland AR-200 owner manual Installation, Attaching the Rubber Feet Included Items

Page 10

Installation

Attaching the Rubber Feet (Included Items)

Attach these as required, such as when you’re using the AR-200 without mounting it on a rack or the like.

Peel off the double-sided tape from the rubber feet and affix the rubber feet at the locations shown in the following figure.

fig.set-01

Bottom Chassis

Rack Mounting (Important Notes on Heat Radiation)

When you are mounting the unit on a rack or the like, give attention to the following points to ensure efficient cooling.

Install in a well-ventilated location.

Avoid mounting in a sealed rack. Warm air within the rack cannot escape and is sucked into the unit again, making efficient cooling impossible.

When you are using a stacked mounting arrangement, be especially sure to provide for adequate ventilation within the rack to keep discharged air from being sucked back into the unit. If the back surface of the rack cannot be kept open, then provide a ventilation port or ventilation fan at the upper area of the back surface of the rack, where warm air accumulates.

When you are using the unit in a portable case or rack, remove the covers from the front and back surfaces of the case, so that the front and back surfaces of the unit are not obstructed.

If an error message informing you of a dangerous rise in temperature appears (p. 52), then heat-dissipating measures are needed. Refer to the cautions just described and check the installed state of the unit and the rack.

*When placing the unit on the rack, be careful not to pinch your fingers.

*For more information about installation, also see "Placement" in the Usage Notes (p. 4).

10

Image 10
Contents Page Using the Unit Safely Page Maintenance Power SupplyPlacement Before Using PC CardsContents Midi Implementation Midi Implementation Chart Specification Troubleshooting Error messages Regarding CardsMode SW Settings AppendicesMain Features Rear panel Panel DescriptionsFront panel Bottom chassisTurning On the Power Refer also to DC power supply pAttaching the Rubber Feet Included Items InstallationRack Mounting Important Notes on Heat Radiation Attaching the Card Protector InstallationRack-Mounting the AR-200 Examples of Usage and Connection for the AR-200 Using the Control Input and Output ConnectorsDevice with the AR-200 Control Output Connectors p Together with Other Equipment System ExamplesControlling the AR-200 With Midi Signals Midi Control p Using the Midi ConnectorsExamples of Usage and Connection for the AR-200 Repeat Playback of the Same Phrase What You Can Do Usage TipsPlaying a Variety of Phrases in Succession Card Storage Times and Number of Phrases Cards Handled by the AR-200Types of Usable Cards Formatting a CardImportant Notes on Handling Cards Procedure for Formatting CardsCards Handled by the AR-200 If You’re Using a Legacy Model Card Compatibility with Other Models in the AR SeriesRecording Units-Phrases Connecting External DevicesRecording Audio Monitor Output During Recording and Recording StandbyRecording Audio Procedure for RecordingRDAC-Gradesampling frequency REC Mode SW-3 Amount of cardRDAC-Mode Signal Processing FormatREC Mode SW 4 Card Audio Recording Time Chart P.53What is mono recording Recording Type Stereo/MonoREC Mode SWLine Thru Output Important Notes on ProcedureSwitching the Power On Making ConnectionsChecking What You Recorded Information Recorded on the CardPlayback Using the Panel Manual Playback Press the Play button and the phrase will playbackDeleting Single Phrases Deleting PhrasesDeleting All Phrases Recording and Playing Midi Data Midi Phrase What is a Midi Phrase?Procedure for Recording Midi PhrasesRecording and Playing Midi Data Midi Phrase Procedure for Playing Back MidiPlayback Using Control Input and Other Input Manual playbackPlayback By Card Data Selecting the Control Input Mode AR-200 SettingsAssigning Phrases to the Terminals Basic Operation of Direct Playback Reverse Priority Operational Specifications for Direct Playback Last-InOperational Specifications for Control Input Playback Priority OrderConnectors Used in Binary Playback What Is Binary Playback?/Use and ApplicationsSpecifying Phrases in Binary Notation Binary Playback To Specify Phrases with Binary Signals Operational Specifications of Binary PlaybackBasic Operation of Binary Playback Phrase Number / Binary Signal chart Repeated Playback of Phrases Interval Playback Operational Specifications of Interval PlaybackWhat is Terminal Rec/Use and Applications Basic Operation of Interval PlaybackConnectors Used in Terminal Rec Connecting EquipmentOperational Specifications for Terminal Rec Presence or Absence of PhrasesPlayback Switching the Terminal Recording ModeErase 001 00000000 Output of Busy Out Signals In Dual Mono Mode p What is the Busy Out Signal?/ Connecting DevicesImportant Note on Using the Control Input and Output Ports Starting Another Device Busy OutOutput of Control Out Signals In Dual Mono Mode p What is the Control Out Signal? Connecting DevicesControlling Another Device Control Out Memo Applications Guide Playback of Phrases Using Midi Signals Controlling the AR-200 with Midi Signals Midi controlWhat is Midi Control?/What You Can Do Using Midi Control When Playing Back Midi Phrases Using Midi Signals Controlling the AR-200 with Midi Signals Midi controlAssignment of Phrases to Note Numbers Midi Note Map Procedure for Making the Midi Receive Channel Settings Midi Receive channel Settings Midi channelMidi Control Signals That Can Be Received Receive Messages Midi Note OutExample of Connecting to an Playback with AR-LINK SignalsWhat is AR-LINK?/What You Can Do Using AR-LINK Synchronized Audio PhraseSettings Procedure Selecting the AR-200’s Operation AROther Useful Functions During Phrase Playback Line Out Thru Setting During Phrase PlaybackTo Users of the AR-2000/100 Legacy Models Line Thru Output Specifications Other Useful Functions During Phrase PlaybackAppendices About playback TroubleshootingAbout recording About playback and recording of Midi phrasesOthers TroubleshootingCard made on the AR-3000 Error messages Fig.er-3Card Audio Recording Time Chart Regarding CardsRecorded Phrase Data Settings When a Card Is FormattedAppendices Midi settings AR-3000 settings that can be usedAR-LINK Setting Mode SW Settings Mode Switch SpecificationsControl I/O Connector specifications DC power supplyControl Change Midi ImplementationReceive data Media Player Section Program ChangeMidi Time Code Midi ImplementationMidi Machine Control MMC Transmitted message which are produced Transmitted message which are receivedRecognized message for sync Message not memorized during recording Exclusive Communication Messages received for detecting trouble in Midi connectionTransmit data Midi Recorder Section Parameter Address MapExclusive Address Table Phrase Select AR-200/3000 Midi Implementation Midi Recording Section Specification Specification Input/Output Standard DimentionsIndex AR-LINKInformation AfricaAvis 02235223 ’03-8-7N